Autovon

From Infogalactic: the planetary knowledge core
Jump to: navigation, search
An Autovon telephone keypad with three of the four precedence levels (excluding Routine), plus Flash Override

The Automatic Voice Network (AUTOVON) was a world-wide American military telephone system. The system was built starting in 1963, based on the Army's existing Switch Communications Automated Network (SCAN) system. In June 1966 the Air Defense Command voice network was cut over to the new service.[1] In 1969, AUTOVON switching centers opened in the United Kingdom, and later in other European countries, Asia, the Middle East, and Panama. It was a major part of the Defense Communications System (DCS), providing non-secure switched voice services. The system was replaced in the early 1990s by the Defense Switched Network.

Circuits

AUTOVON used a combination of its own constructed circuits and other lines operated by AT&T Corporation and smaller independent telephone companies, connected to exchanges located far from other civilian or military targets. In the US the cables were predominantly L-carrier coaxial multiplex built by AT&T, who also used them to carry about one third of all civilian long-distance calls, as their capacity was much higher than the military needed. Although unused, some of the cables remain today and the routes are visible on satellite photos. The system's traffic was transported over many media other than underground cable, including microwave links, open wire and, near the end of the system's life, fiber optic. Contrary to stories of underground concrete cable ducts,[citation needed] most of the cable was directly buried without added concrete, relying instead on the natural protection of soil.

Most of the cable repeater huts have been sold to private interests, to round out existing parcels, or as possible build-to-suit tower sites, etc. AT&T has been filling the small underground portion before sale, unless they sell to a major company. The junctions for AUTOVON are also being sold into private ownership, with a few exceptions. Most are stripped of all the equipment, although the AUTOVON junction in Mounds, Oklahoma was sold with all the old equipment in place.Lua error in package.lua at line 80: module 'strict' not found.

The telephone switches used were initially a 4 wire version of 5XB switch, replaced in the early 1970s after the more versatile 1ESS switch had shown its reliability.

Multilevel precedence and preemption

The AUTOVON system provided a facility for placing calls with multilevel precedence and preemption (MLPP). If in the public switched telephone network a caller encounters congestion because no circuits are available, the caller typically receives the reorder tone ("fast-busy" signal) and is unable to reach the called party. In military networks such an event was not acceptable, as some calls must always be completed.

AUTOVON included four message precedence levels: Routine, Priority, Immediate and Flash, and had an additional capability called Flash Override. These levels were activated using the buttons in an additional column of the keypad, which produced the dual-tone multi-frequency (DTMF) signals A, B, C, and D:

  • A (697/1633): Flash Override (FO)
  • B (770/1633): Flash (F)
  • C (852/1633): Immediate (I)
  • D (941/1633): Priority (P)

Routine was the level of calls without priority and required no special signaling; the user would only dial the telephone number. Calls with precedence required preceding the telephone number with the desired precedence signal. Calls of increasing precedence could preempt calls of lower priority, giving them a special tone, if need be. For example, if a call was placed with Flash precedence and the route had no available trunks, the switch would preempt a Routine call, and if none in progress, would search for Priority and Immediate type calls. Only when all lines of a switch were already used with Flash or Flash Override precedence would the caller receive a reorder signal.

The authority of a caller to use the precedence levels was granted by complex regulations.[2] Flash Override was not designated as a precedence level, but a capability designed to allow the President of the United States or other National Command Authority to preempt any other traffic in the network in an emergency.

The International Telecommunications Union accepted the MLPP specification as recommendation Q.955.3 in March 1993.[3]

Numbering plan

AUTOVON used a numbering scheme similar to the North American Numbering Plan. The network had its own three-digit area codes for various geographic regions around the world. Each area code covered several three-digit exchange codes, usually corresponding to the central office telephone switches serving each installation. Thus, almost any telephone on a military base could be direct-dialed via AUTOVON. A selected set of telephones were four-wire AUTOVON phones, wired directly into the AUTOVON network. Others could initiate AUTOVON calls with operator assistance.

Though the numbering plan was similar to the U.S. civilian scheme, the routing structure was a very complex polygrid system unlike the civilian office classification scheme. It was barely within the information processing capabilities of the 5XB switch which implemented it. The non-hierarchical routing structure was intended to get around any number of nodes destroyed in war. This system inspired similarly survivable ones for message networks, including in future decades the Internet.

Local base switches would be connected to a few AUTOVON trunks, which the user would access by dialing 8 (or in some cases, 88) before the telephone number. To dial locally a user would dial 9, and to dial using commercial long-distance, 1 (where this was supported). The United States Department of Defense (DoD) charged access to AUTOVON according to a complex billing system, and each base budgeted according to local practice.

See also

References

  1. AT&T (1974) Events in Telephone History
  2. Copy of a 1971 "Official Global Autovon Telephone Directory"
  3. Lua error in package.lua at line 80: module 'strict' not found.

 This article incorporates public domain material from the General Services Administration document "Federal Standard 1037C".

External links