Equilibrium constant

The equilibrium constant of a chemical reaction is the value of the reaction quotient when the reaction has reached equilibrium. An equilibrium constant value is independent of the analytical concentrations of the reactant and product species in a mixture, but depends on temperature and on ionic strength. Known equilibrium constant values can be used to determine the composition of a system at equilibrium.

For a general chemical equilibrium

$\alpha A +\beta B ... \rightleftharpoons \rho R+\sigma S ...$

the thermodynamic equilibrium constant can be defined such that, at equilibrium,

$K^\ominus =\frac{{\{R\}} ^\rho {\{S\}}^\sigma ... } {{\{A\}}^\alpha {\{B\}}^\beta ...}$

where curly brackets denote the thermodynamic activities of the chemical species. The right-hand side of this equation corresponds to the reaction quotient Q for arbitrary values of the activities, and becomes the equilibrium constant as shown when the reaction is at equilibrium.

An equilibrium constant is related to the standard Gibbs free energy change for the reaction.

$\Delta G^\ominus=-RT \ln K^\ominus$

If deviations from ideal behaviour are neglected, the activities of solutes may be replaced by concentrations, [A], and the activity quotient becomes a concentration quotient, K_c.

$K_\text{c}=\frac{{[R]} ^\rho {[S]}^\sigma ... } {{[A]}^\alpha {[B]}^\beta ...}$

K_c is defined as equal to the thermodynamic equilibrium constant but with concentrations of reactants and products instead of activities. (K_c appears here to have units of concentration raised to some power while K is dimensionless; however as discussed below under Definitions, the concentration factors in K_c are properly divided by a standard concentration so that K_c is dimensionless also.)

Again assuming ideal behavior, the activity of a solvent may be replaced by its mole fraction, or approximately by 1 in dilute solution. The activity of a pure liquid or solid phase is exactly 1. The activity of a species in an ideal gas phase may be replaced by its partial pressure.

A knowledge of equilibrium constants is essential for the understanding of many chemical systems, as well as biochemical processes such as oxygen transport by hemoglobin in blood and acid-base homeostasis in the human body.

Stability constants, formation constants, binding constants, association constants and dissociation constants are all types of equilibrium constant. See also Determination of equilibrium constants for experimental and computational methods.

Types of equilibrium constants

Cumulative and stepwise formation constants

A cumulative or overall constant, given the symbol β, is the constant for the formation of a complex from reagents. For example, the cumulative constant for the formation of ML₂ is given by

$M+2L \rightleftharpoons ML_2; \quad [ML_2]=\beta_{12}[M][L]^2$

The stepwise constant, K, for the formation of the same complex from ML and L is given by

$ML+L \rightleftharpoons ML_2; \quad [ML_2]=K[ML][L]=K\beta_{11}[M][L][L]=K\beta_{11}[M][L]^2$

It follows that

$\beta_{12}=K\beta_{11}\,$

A cumulative constant can always be expressed as the product of stepwise constants. There is no agreed notation for stepwise constants, though a symbol such as K^L
_ML is sometimes found in the literature. It is best always to define each stability constant by reference to an equilibrium expression.

Competition method

A particular use of a stepwise constant is in the determination of stability constant values outside the normal range for a given method. For example, EDTA complexes of many metals are outside the range for the potentiometric method. The stability constants for those complexes were determined by competition with a weaker ligand.

$ML+L'\rightleftharpoons ML'+L$

$[ML']=K\frac{[ML][L']}{[L]} = K \frac{\beta_{ML}[M][L][L']}{[L]}= K \beta_{ML}[M][L']; \quad \beta_{ML'}=K\beta_{ML}$

The formation constant of [Pd(CN)₄]²⁻ was determined by the competition method.

Association and dissociation constants

In organic chemistry and biochemistry it is customary to use pK_a values for acid dissociation equilibria.

$pK_\text{a}=-\log K_{\text{diss}} = \log (1/K_{\text{diss}})\,$

where K_diss is a stepwise acid dissociation constant. For bases, the base association constant, pK_b is used. For any given acid or base the two constants are related by pK_a + pK_b = pK_w, so pK_a can always be used in calculations.

On the other hand stability constants for metal complexes, and binding constants for host-guest complexes are generally expressed as association constants. When considering equilibria such as

$M + HL\rightleftharpoons ML + H$

it is customary to use association constants for both ML and HL. Also, in generalized computer programs dealing with equilibrium constants it is general practice to use cumulative constants rather than stepwise constants and to omit ionic charges from equilibrium expressions. For example, if NTA, nitrilotriacetic acid, N(CH₂CO₂H)₃ is designated as H₃L and forms complexes ML and MHL with a metal ion M, the following expressions would apply for the dissociation constants.

$H_3L \rightleftharpoons H_2L+H; \quad pK_1=-\log \left(\frac{[H_2L][H]} {[H_3L]} \right)$

$H_2L \rightleftharpoons HL+H; \quad pK_2=-\log \left(\frac{[HL][H]} {[H_2L]} \right)$

$HL \rightleftharpoons L+H; \quad pK_3=-\log \left(\frac{[L][H]} {[HL]} \right)$

The cumulative association constants can be expressed as

$L+H \rightleftharpoons HL; \quad\log \beta_{011} =\log \left(\frac{[HL]}{[L][H]} \right)=pK_3$

$L+2H \rightleftharpoons H_2L; \quad\log \beta_{012} =\log \left(\frac{[H_2L]}{[L][H]^2} \right)=pK_3+pK_2$

$L+3H \rightleftharpoons H_3L; \quad\log \beta_{013} =\log \left(\frac{[H_3L]}{[L][H]^3} \right)=pK_3+pK_2+pK_1$

$M+L \rightleftharpoons ML; \quad\log \beta_{110} =\log \left(\frac{[ML]}{[M][L]} \right)$

$M+L+H \rightleftharpoons MLH; \quad\log \beta_{111} =\log \left(\frac{[MLH]}{[M][L][H]} \right)$

Note how the subscripts define the stoichiometry of the equilibrium product.

Micro-constants

When two or more sites in an asymmetrical molecule may be involved in an equilibrium reaction there are more than one possible equilibrium constants. For example, the molecule L-dopa has two non-equivalent hydroxyl groups which may be deprotonated. Denoting L-Dopa as LH₂, the following diagram shows all the species that may be formed (X=CH₂CH(NH₂)CO₂H)

The first protonation constants are

[L¹H] = k₁₁[L][H], [L²H] = k₁₂[L][H]

The concentration of LH⁻ is the sum of the concentrations of the two micro-species. Therefore, the equilibrium constant for the reaction, the macro-constant, is the sum of the micro-constants.

K₁ = k₁₁ + k₁₂

In the same way,

K₂ = k₂₁ + k₂₂

Lastly, the cumulative constant is

β₂ = K₁K₂ = k₁₁k₂₁ = k₁₂k₂₂

Thus, although there are seven micro-and macro-constants, only three of them are mutually independent. Moreover, the isomerization constant, K_i, is equal to the ratio of the microconstants.

K_i = k₁₁/k₁₂

In L-Dopa the isomerization constant is 0.9, so the micro-species L¹H and L²H have almost equal concentrations at all pH values.

In general a macro-constant is equal to the sum of all the micro-constants and the occupancy of each site is proportional to the micro-constant. The site of protonation can be very important, for example, for biological activity.

Micro-constants cannot be determined individually by the usual methods, which give macro-constants. Methods which have been used to determine micro-constants include:

• blocking one of the sites, for example by methylation of a hydroxyl group, to determine one of the micro-constants
• using a spectroscopic technique, such as infrared spectroscopy, where the different micro-species give different signals.
• applying mathematical procedures to ¹³C NMR data.

pH considerations (Brønsted constants)

pH is defined in terms of the activity of the hydrogen ion

$pH = -\log \{H^+\}\,$

In the approximation of ideal behaviour, activity is replaced by concentration. pH is measured by means of a glass electrode, a mixed equilibrium constant, also known as a Brønsted constant, may result.

$HL \rightleftharpoons L+H; \quad pK =-\log \left(\frac{[L]\{H\}}{[HL]} \right)$

It all depends on whether the electrode is calibrated by reference to solutions of known activity or known concentration. In the latter case the equilibrium constant would be a concentration quotient. If the electrode is calibrated in terms of known hydrogen ion concentrations it would be better to write p[H] rather than pH, but this suggestion is not generally adopted.

Hydrolysis constants

In aqueous solution the concentration of the hydroxide ion is related to the concentration of the hydrogen ion by

$K_\text{W}=[H][\text{OH}]$

$[\text{OH}]=K_\text{W}[\text{H}]^{-1}\,$

The first step in metal ion hydrolysis can be expressed in two different ways

1. $M(\text{H}_2\text{O}) \rightleftharpoons M(\text{OH}) +H; \quad [M(\text{OH})]=\beta^*[M][\text{H}]^{-1}$
2. $M+\text{OH} \rightleftharpoons M(\text{OH}); \quad [M(\text{OH})]=K[M][\text{OH}]=K K_\text{W}[M][\text{H}]^{-1}$

It follows that β^* = K K_W. Hydrolysis constants are usually reported in the β^* form and this leads to them appearing to have strange values. For example, if lg K = 4 and lg K_W = −14, lg β^* = 4 + (−14) = −10. In general when the hydrolysis product contains n hydroxide groups lg β^* = lg K + n lg K_W

Conditional constants

Conditional constants, also known as apparent constants, are concentration quotients which are not true equilibrium constants but can be derived from them. A very common instance is where pH is fixed at a particular value. For example, in the case of iron(III) interacting with EDTA, a conditional constant could be defined by

$K_{\text{cond}}=\frac{[\mbox{Total Fe bound to EDTA}]}{[\mbox{Total Fe not bound to EDTA}]\times [\mbox{Total EDTA not bound to Fe}] }$

This conditional constant will vary with pH. It has a maximum at a certain pH. That is the pH where the ligand sequesters the metal most effectively.

In biochemistry equilibrium constants are often measured at a pH fixed by means of a buffer solution. Such constants are, by definition, conditional and different values may be obtained when using different buffers.

Gas phase equilibria

For equilibria in a gas phase, fugacity, f, is used in place of activity. However, fugacity has the dimension of pressure, so it must be divided by a standard pressure, usually 1 bar, in order to produce a dimensionless quantity, f / p. An equilibrium constant is expressed in terms of the dimensionless quantity. For example, for the equilibrium 2NO₂ ⇌ N₂O₄,

$f_{\text{N}_2\text{O}_4}/p^\ominus = K \left(f_{\text{NO}_2}/{p^\ominus}\right)^2$

Fugacity is related to partial pressure, p, by a dimensionless fugacity coefficient ϕ: f = ϕ p. Thus, for the example,

$K=\frac{\phi_{\text{N}_2\text{O}_4} p_{\text{N}_2\text{O}_4}/{p^\ominus}}{\left(\phi_{\text{NO}_2}p_{\text{NO}_2}/{p^\ominus}\right)^2}$

Usually the standard pressure is omitted from such expressions. Expressions for equilibrium constants in the gas phase then resemble the expression for solution equilibria with fugacity coefficient in place of activity coefficient and partial pressure in place of concentration.

$K=\frac{\phi_{\text{N}_2\text{O}_4} p_{\text{N}_2\text{O}_4}}{\left(\phi_{\text{NO}_2}p_{\text{NO}_2}\right)^2}$

Thermodynamics

Definitions

For a general chemical equilibrium

$\alpha A +\beta B ... \rightleftharpoons \rho R+\sigma S ...$

the thermodynamic definition of the equilibrium constant is that, at equilibrium,

$K^\ominus=\frac{{\{R\}} ^\rho {\{S\}}^\sigma ... } {{\{A\}}^\alpha {\{B\}}^\beta ...}$

where {A} is the activity, at equilibrium, of the chemical species A, etc. It is conventional to put the activities of the products in the numerator and those of the reactants in the denominator. Since activity is a dimensionless quantity, the thermodynamic equilibrium constant, K, is also a dimensionless quantity. This is important because K is related to the standard free energy change, ΔG, for the reaction.

$\Delta G^\ominus =-RT \ln K^\ominus$

R is the gas constant and T the absolute or thermodynamic temperature. Taking the logarithm of K is only possible when K has no dimensions, that is, when it is a pure (positive) number. However it is often more convenient to use concentrations (or partial pressures in the gas phase) than activities, so the equilibrium expression may be written as the product of three components, a reaction quotient of equilibrium concentrations, Q^E, a quotient of activity factors, Γ, and a quotient of standard concentrations, C⁰.

$K^\ominus=\frac{[R] ^\rho [S]^\sigma ... } {[A]^\alpha [B]^\beta ...} \times \frac{{\gamma_R}^\rho {\gamma_S}^\sigma ...}{{\gamma_A}^\alpha {\gamma_B}^\beta ...} \times \frac{\left ({c^\ominus_A}\right ) ^\alpha \left({c^\ominus_B}\right)^\beta ...} {\left ({c^\ominus_R}\right ) ^\rho \left({c^\ominus_S}\right)^\sigma ...} = Q^E \Gamma C^0$

The symbol [A] stands for a generalized concentration or partial pressure of the chemical species A, The activity coefficients, γ, are dimensionless and c_A stands for the standard concentration or standard partial pressure. By convention the standard concentrations have a value of 1 mol/dm³ (or 1 atm), so the third factor, C⁰, has a numerical value of 1 and units that are the reciprocal of the units of the concentration quotient. K remains dimensionless. so the expression simplifies to

$K^\ominus=Q^E \times \Gamma \times 1 = Q^E\Gamma$

Variation of log K_c of acetic acid with ionic strength

It follows that the "Concentration constant", K_c, is related to the thermodynamic equilibrium constant by

$K_\text{c}= \frac{[R] ^\rho [S]^\sigma ... } {[A]^\alpha [B]^\beta ...} \times C^0= \frac{K^\ominus}{\Gamma}$

Note that when K_c is defined in this way it has no dimension, so log K_c is permissible.

When an equilibrium constant value is to be determined, there are three options for dealing with the activity coefficients.

1. Use known or calculated activity coefficients, together with concentrations of reactants. For equilibria in solution estimates of the activity coefficients of charged species can be obtained using Debye–Hückel theory, an extended version, or SIT theory. For uncharged species, the activity coefficient γ₀ mostly follows a "salting-out" model: log₁₀(γ₀) = b I where I stands for ionic strength.
2. Assume that the activity coefficients are all equal to 1. This is acceptable when all species are uncharged and the solvent has low polarity.
3. For equilibria in solution use a medium of high ionic strength. In effect this redefines the standard state as referring to the medium. Activity coefficients in the standard state are, by definition, equal to 1. The value of an equilibrium constant determined in this manner is dependent on the ionic strength. When published constants refer to an ionic strength other than the one required for a particular application, they may be adjusted by means of specific ion theory (SIT) and other theories.

Units

K_c appears to have the dimension of concentration to the power z, the difference of the sums of the powers in the numerator and denominator: z = ρ + σ + ... − (α + β + ...). It must in fact be dimensionless or it would not be possible to take its logarithm. The illusion is the result of omitting the standard concentrations from the defining expression. Nevertheless it is not unusual, particularly in texts relating to biochemical equilibria, to see a value quoted with a dimension. Some examples are as follows

$A + B \rightleftharpoons AB; \quad K_\text{c} = \frac{[AB]}{[A][B]} /\text{M}^{-1}$

$A + 2B \rightleftharpoons AB_2; \quad K_\text{c} = \frac{[AB_2]}{[A][B]^2} /\text{M}^{-2}$

where the symbol M signifies a molar concentration (1 M = 1 mol dm⁻³). In writing these expressions, there is an implicit assumption that the quotient of activity coefficients is equal to 1. Furthermore, the subscript c is often omitted, implying that the concentration quotient is a thermodynamic equilibrium constant, in the sense defined above. In these cases, the unit in effect specifies the concentration scale to which the concentrations [A], [B], etc. refer. Implicitly, the standard concentrations are on that scale, too.

In speciation calculations one must define the equilibrium constant as a quotient of concentrations, K = Q^E. Then, the equilibrium constant has dimensions, such as M⁻¹ (mol⁻¹ dm³) or mM⁻¹ (mmol⁻¹ dm³), a unit sometimes used in biochemistry. For example, for the formation of an adduct A + B ⇌ AB the concentrations [A] and [B] can be calculated by solving the equations of mass-balance.

$\begin{align} T_A & = [A]+K[A][B]\\ T_B & = [B]+K[A][B] \end{align}$

where T_A and T_B are the analytical concentrations of the reagents A and B and the numerical value of K is known.. Each term in the expressions should have the same unit of concentration so that the numerical values of the concentrations can be calculated. In this example, assuming molar concentrations, the product concentration [AB] = K[A][B] has dimension M⁻¹ × M × M = M, the same as T_A, T_B, [A] and [B].

Derivation of equilibrium constant expression

Temperature, T, is assumed to be constant in the following treatment.

Thermodynamic equilibrium is characterized by the free energy for the whole (closed) system being a minimum. For systems at constant pressure the Gibbs free energy is minimum. The slope of the reaction free energy, δG_r with respect to the reaction coordinate, ξ, is zero when the free energy is at its minimum value.

$\delta G_\text{r}=\left(\frac{\partial G}{\partial \xi }\right)_{T,P}; \quad \delta G_r(\text{Eq})=0$

The free energy change, δG_r, can be expressed as a weighted sum of chemical potentials, the partial molar free energies of the species in equilibrium. The potential, μ_i, of the ith species in a chemical reaction is the partial derivative of the free energy with respect to the number of moles of that species, N_i

$\mu_i=\left(\frac{\partial G}{\partial N_i}\right)_{T,P}$

A general chemical equilibrium can be written as

$\sum_j n_j \text{Reactant}_j\rightleftharpoons \sum_k m_k \text{Product}_k \quad \equiv \quad \alpha A+\beta B...\rightleftharpoons \rho R+\sigma S ...$

where n_j are the stoichiometric coefficients of the reactants in the equilibrium equation, and m_j are the coefficients of the products. The value of δG_r for these reactions is a function of the chemical potentials of all the species.

$\delta G_r = \sum_k m_k \mu_k \, - \sum_j n_j \mu_j$

The chemical potential, μ_i, of the ith species can be calculated in terms of its activity, a_i.

$\mu_i = \mu_i^\ominus + RT \ln a_i$

μ_i is the standard chemical potential of the species, R is the gas constant and T is the temperature. Setting the sum for the reactants j to be equal to the sum for the products, k, so that δG_r(Eq) = 0

$\sum_j n_j(\mu_j^\ominus +RT\ln a_j)=\sum_k m_k(\mu_k^\ominus +RT\ln a_k)$

Rearranging the terms,

$\sum_k m_k\mu_k^\ominus-\sum_j n_j\mu_j^\ominus =-RT \left(\sum_k \ln {a_k}^{m_k}-\sum_j \ln {a_j}^{n_j}\right)$

$\Delta G^\ominus = -RT \ln K.$

This relates the standard Gibbs free energy change, ΔG to an equilibrium constant, K, the reaction quotient of activity values at equilibrium.

$\Delta G^\ominus = \sum_k m_k\mu_k^\ominus-\sum_j n_j\mu_j^\ominus$

$\ln K= \sum_k \ln {a_k}^{m_k}-\sum_j \ln {a_j}^{n_j}; K=\frac{\prod_k {a_k}^{m_k}}{\prod_j {a_j}^{n_j}} \equiv \frac{{\{R\}} ^\rho {\{S\}}^\sigma ... } {{\{A\}}^\alpha {\{B\}}^\beta ...}$

Temperature dependence

The van 't Hoff equation.

$\frac{d \ln K}{dT}\ = \frac{\Delta H^\ominus}{RT^2} \mbox{ or } \frac{d \ln K}{d(1/T)}\ = -\frac{\Delta H^\ominus}{R}$

shows that when the reaction is exothermic (ΔH is negative), then K decreases with increasing temperature, in accordance with Le Chatelier's principle. It permits calculation of the reaction equilibrium constant at temperature T₂ if the reaction constant at T₁ is known and the standard reaction enthalpy can be assumed to be independent of temperature even though each standard enthalpy change is defined at a different temperature. However, this assumption is valid only for small temperature differences T₂ − T₁. In fact standard thermodynamic arguments can be used to show that

$\left(\frac{\partial H}{\partial T} \right)_p=C_p$

where C_p is the heat capacity at constant pressure. The equilibrium constant is related to the standard Gibbs energy change of reaction as

$\ \Delta G^\ominus = -RT \ln K$

where ΔG is the standard Gibbs free energy change of reaction, R is the gas constant, and T the absolute temperature.

If the equilibrium constant has been determined and the standard reaction enthalpy has also been determined, by calorimetry, for example, this equation allows the standard entropy change for the reaction to be derived.

A more complex formulation

The calculation of K at a particular temperature from a known K at another given temperature can be approached as follows if standard thermodynamic properties are available. The effect of temperature on equilibrium constant is equivalent to the effect of temperature on Gibbs energy because:

$\ln K = {{-\Delta_\mathrm{r} G^\ominus} \over {RT}}$

where Δ_rG is the reaction standard Gibbs energy, which is the sum of the standard Gibbs energies of the reaction products minus the sum of standard Gibbs energies of reactants.

Here, the term "standard" denotes the ideal behaviour (i.e., an infinite dilution) and a hypothetical standard concentration (typically 1 mol/kg). It does not imply any particular temperature or pressure because, although contrary to IUPAC recommendation, it is more convenient when describing aqueous systems over wide temperature and pressure ranges.

The standard Gibbs energy (for each species or for the entire reaction) can be represented (from the basic definitions) as:

$G_{T_2}^\ominus = G_{T_1}^\ominus-S_{T_1}^\ominus(T_2-T_1)-T_2 \int^{T_2}_{T_1} {{C_P^\ominus} \over {T}}\,dT + \int^{T_2}_{T_1} C_p^\ominus\,dT$

In the above equation, the effect of temperature on Gibbs energy (and thus on the equilibrium constant) is ascribed entirely to heat capacity. To evaluate the integrals in this equation, the form of the dependence of heat capacity on temperature needs to be known.

Now, if one expresses the standard heat capacity C_p, as a function of absolute temperature using correlations of the following forms:

• For pure substances (solids, gas, liquid):

$C_p^\ominus = A + BT + CT^{-2}$

• For ionic species at T < 200 deg C:

$C_p^\ominus = (4.186a+b\breve{S}^\ominus_{T_1}) {{(T_2-T_1)} \over {\ln(T_2/T_1)}}$

then the integrals can be evaluated and the following final form is obtained:

$G_{T_2}^\ominus = G_{T_1}^\ominus + (C_p^\ominus - S_{T_1}^\ominus)(T_2-T_1) - T_2 \ln{({T_2}/{T_1})}C_p^\ominus$

The constants A, B, C, a, b and the absolute entropy, $\breve{S}$₂₉₈, required for evaluation of C_p(T), as well as the values of G_{298 K} and S_{298 K} for many species are tabulated in the literature.

Pressure dependence

The pressure dependence of the equilibrium constant is usually weak in the range of pressures normally encountered in industry, and therefore, it is usually neglected in practice. This is true for condensed reactant/products (i.e., when reactants and products are solids or liquid) as well as gaseous ones.

For a gaseous-reaction example, one may consider the well-studied reaction of hydrogen with nitrogen to produce ammonia:

N₂ + 3H₂ ⇌ 2NH₃

If the pressure is increased by an addition of an inert gas, then neither the composition at equilibrium nor the equilibrium constant are appreciably affected (because the partial pressures remain constant, assuming an ideal-gas behaviour of all gases involved). However, the composition at equilibrium will depend appreciably on pressure when:

• the pressure is changed by compression of the gaseous reacting system, and
• the reaction results in the change of the number of moles of gas in the system.

In the example reaction above, the number of moles changes from 4 to 2, and an increase of pressure by system compression will result in appreciably more ammonia in the equilibrium mixture. In the general case of a gaseous reaction:

$\alpha A + \beta B \rightleftharpoons \sigma S + \tau T\,$

the change of mixture composition with pressure can be quantified using:

$K_p = \frac{{p_S}^\sigma {p_T}^\tau} {{p_A}^\alpha {p_B}^\beta} = \frac{{X_S}^\sigma {X_T}^\tau} {{X_A}^\alpha {X_B}^\beta} P^{\sigma+\tau-\alpha-\beta} = K_X P^{\sigma+\tau-\alpha-\beta}$

where p denote the partial pressures of the components, P is the total system pressure, X denote the mole fraction, K_p is the equilibrium constant expressed in terms of partial pressures and K_X is the equilibrium constant expressed in terms of mole fractions.

The above change in composition is in accordance with Le Chatelier's principle and does not involve any change of the equilibrium constant with the total system pressure. Indeed, for ideal-gas reactions K_p is independent of pressure.

Pressure dependence of the water ionization constant at 25 °C. In general, ionization in aqueous solutions tends to increase with increasing pressure.

In a condensed phase, the pressure dependence of the equilibrium constant is associated with the reaction molar volume. For reaction:

$\alpha A + \beta B \rightleftharpoons \sigma S + \tau T$

the reaction molar volume is:

$\Delta \bar{V} = \sigma \bar{V}_S + \tau \bar{V}_T - \alpha \bar{V}_A - \beta \bar{V}_B$

where V denotes a partial molar volume of a reactant or a product.

For the above reaction, one can expect the change of the reaction equilibrium constant (based either on mole-fraction or molal-concentration scale) with pressure at constant temperature to be:

$\left(\frac{\partial \ln K_X}{\partial P} \right)_T = \frac{-\Delta \bar{V}} {RT}.$

The matter is complicated as partial molar volume is itself dependent on pressure.

Data sources

IUPAC SC-Database A comprehensive database of published data on equilibrium constants of metal complexes and ligands

NIST Standard Reference Database 46 Critically Selected Stability Constants of Metal Complexes

Inorganic and organic acids and bases pKa data in water and DMSO

NASA Glenn Thermodynamic Database webpage with links to (self-consistent) temperature-dependent specific heat, enthalpy, and entropy for elements and molecules

See also

• Determination of equilibrium constants
• Stability constants of complexes
• Equilibrium fractionation

External links

• Science Aid: Equilibrium Constants Explanation of Kc and Kp for High School level