Ice yachting

From Infogalactic: the planetary knowledge core
Jump to: navigation, search

Lua error in package.lua at line 80: module 'strict' not found.

Ice yachting is the sport of sailing and racing iceboats, also called ice yachts. It is practiced in Austria, Germany, Great Britain, Poland, Norway and Sweden, to some extent, and is very popular in the Netherlands and on the Gulf of Finland, but its highest development is in the United States and Canada. The Dutch ice yacht is a flat-bottomed boat resting crosswise upon a planking about three feet wide and sixteen long, to which are affixed four steel runners, one each at bow, stern and each end of the planking. The rudder is a fifth runner fixed to a tiller. Heavy mainsails and jibs are generally used and the boat is built more for safety than for speed. The iceboat of the Gulf of Finland is a V-shaped frame with a heavy plank running from bow to stern, in which the mast is stepped. The stern or steering runner is worked by a tiller or wheel. The sail is a large lug and the boom and gaff are attached to the mast by travelers. The passengers sit upon planks or rope netting. According to some,[who?] the Russian boats were faster than the Dutch-built ice yachts.

Ice sailing in the Netherlands in 1938.
Ice sailing on Lake Balaton, Hungary

In 1790, ice yachting was in vogue on the Hudson River, its headquarters being at Poughkeepsie, New York. The type was a square box on three runners, the two forward, ones being nailed to the box and the third acting as a rudder operated by a tiller. The sail was a flatheaded sprit. This primitive style was in general use until 1853, when triangular frames with boxes for the crew aft and jib and mainsail rig were introduced. A heavy, hard-riding type soon developed, with short gaffs, low sails, large jibs and booms extending far over the stern. It was over-canvassed and the mast was stepped directly over the runner plank, bringing the centre of sail-balance so far aft that the boats were apt to run away, and the over-canvassing frequently caused the windward runner to swing up into the air to a dangerous height. The largest and fastest example of this type, which prevailed until 1879, was Commodore J. A. Roosevelt's first Icicle, which measured 69 ft (21 m) overall and carried 1,070 sq ft (99 m2) of canvas. In 1879, H. Relyea built the Robert Scott, which had a single backbone and guy wires, and it became the model for all Hudson River ice yachts. Masts were now stepped farther forward, jibs were shortened, booms were cut down, and the center of sail-balance was brought more inboard and higher up, causing the centers of effort and resistance to come more in harmony. The shallow steering-box became elliptical. In 1881 occurred the first race for the American Challenge Pennant, which represents the championship of the Hudson River; the clubs that competed included the Hudson River, North Shrewsbury, Orange Lake, Newburgh and Carthage Ice Yacht Clubs. The races are usually sailed five times round a triangle of which each leg measures one mile, at least two of the legs being to windward. Ice yachts are divided into four classes, carrying respectively 600 sq ft (60 m2) of canvas or more, between 450 and 600, between 300 and 450, and less than 300 sq ft (30 m2). Ice yachting is very popular on the Great Lakes, both in the United States and Canada, the Kingston, Ontario Club having a fleet of over 25 sail. Other important centers of the sport are the Lake Geneva, Wisconsin area, with an average of twenty-five sailing days a season for the last five years, Lakes Minnetonka and White Bear in Minnesota, Lakes Winnebago and Pepin in Wisconsin, Bar Harbor Lake in Maine, the St. Lawrence River, Quinte Bay and Lake Champlain.

A modern ice yacht is made of a single-piece backbone the entire length of the boat, and a runner-plank upon which it rests at right angles, the two forming a kite-shaped frame. The best woods for these pieces are basswood, butternut, and pine. They are cut from the log in such a way that the heart of the timber expands, giving the planks a permanent curve, which, in the finished boat, is turned upward. The two forward runners, usually made of soft cast iron and about 2 ft (1 m). 7 in. long and 24 in high, are set into oak frames a little over 5 feet long and 5 inches high. The runners have a cutting edge of 90%, though a V-shaped edge is often preferred for racing. The rudder is a runner about 3 ft (1 m). 7 in. long, worked by a tiller, sometimes made very long, 7½ feet not being uncommon. This enables the helmsman to lie in the box at full length and steer with his feet, leaving his hands free to tend the sheet. Masts and spars are generally made hollow for racing-yachts and the rigging is pliable steel wire. The sails are of 10-ounce duck for a boat carrying 400 sq ft (40 m2) of canvas. They have very high peaks, short hoists and long booms. The mainsail and jib rig is general, but a double-masted lateen rig has been found advantageous. The foremost ice-yacht builder of America was G. E. Buckhout of Poughkeepsie.[citation needed]

Ice sailing on Lake Balaton

An ice yacht about 40 ft (12 m) in length will carry six or seven passengers or crew, who are distributed in such a manner as to preserve the balance of the boat. In a good breeze the crew lie out on the windward side of the runner-plank to balance the boat, and reduce the pressure on the leeward runner. A course of 20 miles (32 km) with many turns has been sailed on the Hudson in less than 48 minutes, the record for a measured mile with flying start being at the rate of about 72 miles (116 km) an hour. In a high wind, however, ice yachts often move at the rate of 85 and even 90 miles (145 km) an hour[citation needed].

On the bays near New York, a peculiar kind of iceboat has developed, called scooter, which may be described as a toboggan with a sail. A typical scooter is about 15 ft (5 m) long with an extreme beam of 5 ft (2 m), perfectly oval in form and flat. It has mainsail and jib carried on a mast 9 or 10 feet long and set well aft, and is provided with two long parallel metal runners. There is no rudder, the scooter being steered entirely by trimming the sails, particularly the jib. As the craft is flat and buoyant, it sails well in water, and can thus be used on very thin ice without danger. A speed of 50 km/h (31 mph) has been attained by a scooter.

See also

References

  • Public Domain This article incorporates text from a publication now in the public domainLua error in package.lua at line 80: module 'strict' not found.

External links