SIMM

This article is about a type of memory module for computers. For other uses, see SIMM (disambiguation).

File:SIMM 30 68 72.png

30-pin, proprietary Apple 68-pin, and 72-pin SIMMs

A SIMM, or single in-line memory module, is a type of memory module containing random-access memory used in computers from the early 1980s to the late 1990s. It differs from a dual in-line memory module (DIMM), the most predominant form of memory module today, in that the contacts on a SIMM are redundant on both sides of the module. SIMMs were standardised under the JEDEC JESD-21C standard.

Most early PC motherboards (8088-based PCs, XTs, and early ATs) used socketed DIP chips for DRAM. As computer memory capacities grew, memory modules were used to save motherboard space and ease memory expansion. Instead of plugging in eight or nine single DIP chips, only one additional memory module was needed to increase the memory of the computer.

History

SIMMs were invented in 1983 by Wang Laboratories, who were granted a patent in April 1987. The original memory modules were built upon ceramic and had pins, i.e. single in-line package (SIP) packaging. Later the modules were built on standard PCB material. Perhaps because the pins often bent or broke during installation, or were more expensive to manufacture, vendors replaced the pins with edge connectors. SIMMs using pins are usually called SIP or SIPP memory modules to distinguish them from the more common modules using edge connectors.

The first variant of SIMMs has 30 pins and provides 8 bits of data (plus a 9th error-detection bit in parity SIMMs). They were used in AT-compatible (286-based, e.g., Wang APC), 386-based, 486-based, Macintosh Plus, Macintosh II, Quadra and Atari STE microcomputers, and Wang VS minicomputers.

The second variant of SIMMs has 72 pins and provides 32 bits of data (36 bits in parity and ECC versions). These appeared first in the early 1990s in the IBM PS/2, and later in systems based on the 486, Pentium, Pentium Pro, early Pentium II, and contemporary/competing chips of other brands. By the mid 90s, 72-pin SIMMs had replaced 30-pin SIMMs in new-build computers, and were starting to themselves be replaced by DIMMs.

Non-IBM PC computers such as UNIX workstations may use proprietary non-standard SIMMs. The Macintosh IIfx uses proprietary non-standard SIMMs with 64 pins.

DRAM technologies used in SIMMs include FPM (Fast Page Mode memory, used in all 30-pin and early 72-pin modules), and the higher-performance EDO DRAM (used in later 72-pin modules).

Due to the differing data bus widths of the memory modules and some processors, sometimes several modules must be installed in identical pairs or in identical groups of four to fill a memory bank. The rule of thumb is a 286, 386SX, 68000 or low-end 68020 / 68030 (e.g. Atari, Mac LC) system (using a 16 bit wide data bus) would require two 30-pin SIMMs for a memory bank. On 386DX, 486, and full-spec 68020 through 68060 (e.g. Amiga 4000, Mac II) systems (32 bit data bus), either four 30-pin SIMMs or one 72-pin SIMM are required for one memory bank. On Pentium systems (data bus width of 64 bits), two 72-pin SIMMs are required. However, some Pentium systems have support for a "half bank mode", in which the data bus would be shortened to only 32 bits to allow operation of a single SIMM. Conversely, some 386 and 486 systems use what is known as "memory interleaving", which requires twice as many SIMMs and effectively doubles the bandwidth.

The earliest SIMM sockets were conventional push-type sockets. These were soon replaced by ZIF sockets in which the SIMM was inserted at an angle, then tilted into an upright position. To remove one, the two metal or plastic clips at each end must be pulled to the side, then the SIMM must be tilted back and pulled out (low-profile sockets reversed this convention somewhat, like SODIMMs - the modules are inserted at a "high" angle, then pushed down to become more flush with the motherboard). The earlier sockets used plastic retainer clips which were found to break, so steel clips replaced them.

Some SIMMs support presence detect (PD). Connections are made to some of the pins that encode the capacity and speed of the SIMM, so that compatible equipment can detect the properties of the SIMM. PD SIMMs can be used in equipment which does not support PD; the information is ignored. Standard SIMMs can easily be converted to support PD by fitting jumpers, if the SIMMs have solder pads to do so, or by soldering wires on.

30-pin SIMMs

File:Atari STE 256kB RAM 1.jpg

30-pin SIMM, 256 KB capacity

File:SIMM Bank.jpg

Two 30-pin SIMM slots on an IBM PS/2 model 50 motherboard

Standard sizes: 256 KB, 1 MB, 4 MB, 16 MB

30-pin SIMMS have 12 address lines, which can provide a total of 24 address bits. With an 8 bit data width, this leads to an absolute maximum capacity of 16 MB for both parity and non-parity modules (the additional redundancy bit chip usually does not contribute to the usable capacity).

30-pin SIMM Memory Module

Pin #	Name	Signal Description		Pin #	Name	Signal Description
1	VCC	+5 VDC		16	DQ4	Data 4
2	/CAS	Column Address Strobe		17	A8	Address 8
3	DQ0	Data 0		18	A9	Address 9
4	A0	Address 0		19	A10	Address 10
5	A1	Address 1		20	DQ5	Data 5
6	DQ1	Data 1		21	/WE	Write Enable
7	A2	Address 2		22	VSS	Ground
8	A3	Address 3		23	DQ6	Data 6
9	VSS	Ground		24	A11	Address 11
10	DQ2	Data 2		25	DQ7	Data 7
11	A4	Address 4		26	QP*	Data parity out
12	A5	Address 5		27	/RAS	Row Address Strobe
13	DQ3	Data 3		28	/CASP*	Parity Column Address Strobe
14	A6	Address 6		29	DP*	Data parity in
15	A7	Address 7		30	VCC	+5 VDC

^* Pins 26, 28 and 29 are not connected on non-parity SIMMs.

72-pin SIMMs

File:Edoram.jpg

72-pin EDO DRAM SIMM

Standard sizes: 1 MB, 2 MB, 4 MB, 8 MB, 16 MB, 32 MB, 64 MB, 128 MB (the standard also defines 3.3 V modules with additional address lines and up to 2 GB)

With 12 address lines, which can provide a total of 24 address bits, two ranks of chips, and 32 bit data output, the absolute maximum capacity is 2²⁷ = 128 MB.

5 V 72-pin SIMM Memory Module

Pin #	Name	Signal Description		Pin #	Name	Signal Description
1	VSS	Ground		37	MDP1*	Data Parity 1 (MD8..15)
2	MD0	Data 0		38	MDP3*	Data Parity 3 (MD24..31)
3	MD16	Data 16		39	VSS	Ground
4	MD1	Data 1		40	/CAS0	Column Address Strobe 0
5	MD17	Data 17		41	/CAS2	Column Address Strobe 2
6	MD2	Data 2		42	/CAS3	Column Address Strobe 3
7	MD18	Data 18		43	/CAS1	Column Address Strobe 1
8	MD3	Data 3		44	/RAS0	Row Address Strobe 0
9	MD19	Data 19		45	/RAS1†	Row Address Strobe 1
10	VCC	+5 VDC		46	NC	Not Connected
11	NU [PD5#]	Not Used [Presence Detect 5 (3v3)]		47	/WE	Read/Write Enable
12	MA0	Address 0		48	NC [/ECC#]	Not Connected [ECC presence (if grounded) (3v3)]
13	MA1	Address 1		49	MD8	Data 8
14	MA2	Address 2		50	MD24	Data 24
15	MA3	Address 3		51	MD9	Data 9
16	MA4	Address 4		52	MD25	Data 25
17	MA5	Address 5		53	MD10	Data 10
18	MA6	Address 6		54	MD26	Data 26
19	MA10	Address 10		55	MD11	Data 11
20	MD4	Data 4		56	MD27	Data 27
21	MD20	Data 20		57	MD12	Data 12
22	MD5	Data 5		58	MD28	Data 28
23	MD21	Data 21		59	VCC	+5 VDC
24	MD6	Data 6		60	MD29	Data 29
25	MD22	Data 22		61	MD13	Data 13
26	MD7	Data 7		62	MD30	Data 30
27	MD23	Data 23		63	MD14	Data 14
28	MA7	Address 7		64	MD31	Data 31
29	MA11	Address 11		65	MD15	Data 15
30	VCC	+5 VDC		66	NC [/EDO#]	Not Connected [EDO presence (if grounded) (3v3)]
31	MA8	Address 8		67	PD1x	Presence Detect 1
32	MA9	Address 9		68	PD2x	Presence Detect 2
33	/RAS3†	Row Address Strobe 3		69	PD3x	Presence Detect 3
34	/RAS2	Row Address Strobe 2		70	PD4x	Presence Detect 4
35	MDP2*	Data Parity 2 (MD16..23)		71	NC [PD (ref)#]	Not Connected [Presence Detect (ref) (3v3)]
36	MDP0*	Data Parity 0 (MD0..7)		72	VSS	Ground

^* Pins 35, 36, 37 and 38 are not connected on non-parity SIMMs.

^†/RAS1 and /RAS3 are only used on two-rank SIMMS: 2, 8, 32, and 128 MB.

^# These lines are only defined on 3.3V modules.

^x Presence Detect signals are detailed in JEDEC Standard.

Proprietary SIMMs

GVP 64-pin

Several CPU cards from Great Valley Products for the Commodore Amiga used special 64-pin SIMMs (32 bits wide, 1, 4 or 16 MB, 60 ns).

Apple 64-pin

Dual-ported 64-pin SIMMs were used in Apple Macintosh IIfx computers to allow overlapping read/write cycles (1, 4, 8, 16 MB, 80 ns).

5V 64-pin Mac IIfx SIMM Memory Module

Pin #	Name	Signal Description		Pin #	Name	Signal Description
1	GND	Ground		33	Q4	Data output bus, bit 4
2	NC	Not connected		34	/W4	Write-enable input for RAM IC 4
3	+5V	+5 volts		35	A8	Address bus, bit 8
4	+5V	+5 volts		36	NC	Not connected
5	/CAS	Column address strobe		37	A9	Address bus, bit 9
6	D0	Data input bus, bit 0		38	A10	Address bus, bit 10
7	Q0	Data output bus, bit 0		39	A11	Address bus, bit 11
8	/W0	Write-enable input for RAM IC 0		40	D5	Data input bus, bit 5
9	A0	Address bus, bit 0		41	Q5	Data output bus, bit 5
10	NC	Not connected		42	/W5	Write-enable input for RAM IC 5
11	A1	Address bus, bit 1		43	NC	Not connected
12	D1	Data input bus, bit 1		44	NC	Not connected
13	Q1	Data output bus, bit 1		45	GND	Ground
14	/W1	Write-enable input for RAM IC 1		46	D6	Data input bus, bit 6
15	A2	Address bus, bit 2		47	Q6	Data output bus, bit 6
16	NC	Not connected		48	/W6	Write-enable input for RAM IC 6
17	A3	Address bus, bit 3		49	NC	Not connected
18	GND	Ground		50	D7	Data input bus, bit 7
19	GND	Ground		51	Q7	Data output bus, bit 7
20	D2	Data input bus, bit 2		52	/W7	Write-enable input for RAM IC 7
21	Q2	Data output bus, bit 2		53	/QB	Reserved (parity)
22	/W2	Write-enable input for RAM IC 2		54	NC	Not connected
23	A4	Address bus, bit 4		55	/RAS	Row address strobe
24	NC	Not connected		56	NC	Not connected
25	A5	Address bus, bit 5		57	NC	Not connected
26	D3	Data input bus, bit 3		58	Q	Parity-check output
27	Q3	Data output bus, bit 3		59	/WWP	Write wrong parity
28	/W3	Write-enable input for RAM IC 3		60	PDCI	Parity daisy-chain input
29	A6	Address bus, bit 6		61	+5V	+5 volts
30	NC	Not connected		62	+5V	+5 volts
31	A7	Address bus, bit 7		63	PDCO	Parity daisy-chain output
32	D4	Data input bus, bit 4		64	GND	Ground

HP LaserJet

72-bit SIMMs with non-standard Presence Detect (PD) connections.

See also

• Dual in-line package (DIP)
• Single in-line package (SIP)
• Zig-zag in-line package (ZIP)
• Dual in-line memory module (DIMM)

External links

• General SIMM Installation Guide