Silicon bandgap temperature sensor

From Infogalactic: the planetary knowledge core
Jump to: navigation, search

The silicon bandgap temperature sensor is an extremely common form of temperature sensor (thermometer) used in electronic equipment. Its main advantage is that it can be included in a silicon integrated circuit at very low cost. The principle of the sensor is that the forward voltage of a silicon diode, which may be the base-emitter junction of a bipolar junction transistor (BJT), is temperature-dependent, according to the following equation:

V_{BE}=V_{G0}\left(1-{\frac{T}{T_0}}\right)+V_{BE0}\left(\frac{T}{T_0}\right)+
    \left(\frac{nKT}{q}\right)\ln\left(\frac{T_0}{T}\right)+
    \left(\frac{KT}{q}\right)\ln\left(\frac{I_C}{I_{C0}}\right) \,

where

T = temperature in kelvin
T0 = reference temperature
VG0 = bandgap voltage at absolute zero
VBE0 = bandgap voltage at temperature T0 and current IC0
K = Boltzmann's constant
q = charge on an electron
n = a device-dependent constant

By comparing the bandgap voltages of two junctions at the same temperature, but at two different currents, IC1 and IC2, many of the variables in the above equation can be eliminated, resulting in the relationship:

\Delta V_{BE}=\frac{KT}{q}\cdot\ln\left(\frac{I_{C1}}{I_{C2}}\right) \,

Note that the junction voltage is a function of current density, i.e. current/junction area, and a similar output voltage can be obtained by operating the two junctions at the same current, if one is of a different area to the other.

A circuit that forces IC1 and IC2 to have a fixed N:1 ratio,[1] gives the relationship:

\Delta V_{BE}=\frac{KT}{q}\cdot\ln\left(N\right) \,

An electronic circuit, such as the Brokaw bandgap reference, that measures ΔVBE can therefore be used to calculate the temperature of the diode. The result remains valid up to about 200 °C to 250 °C, when leakage currents become large enough to corrupt the measurement. Above these temperatures, materials such as silicon carbide can be used instead of silicon.

The voltage difference between two p-n junctions (e.g. diodes), operated at different current densities, is proportional to absolute temperature (PTAT).

PTAT circuits using either BJT or CMOS transistors are widely used in temperature sensors (where we want the output to vary with temperature), and also in bandgap voltage references and other temperature-compensating circuits (where we want the same output at every temperature).[1][2][3][4]

If high precision is not required it is enough to bias a diode with any constant low current and use its −2 mV/˚C thermal coefficient for temperature calculation, however this requires calibration for each diode type. This method is common in monolithic temperature sensors.[citation required]

References

  1. 1.0 1.1 James Bryant. "IC Temperature Sensors". Analog Devices. 2008.
  2. AL.AL, M. B. I. Reaz, S. M. A. Motakabber Mohd Alauddin Mohd Ali. "A Single-chip Proportional to Absolute Temperature Sensor Using CMOS Technology". 2012.
  3. C. Rossi, C. Galup-Montoro, and M. C. Schneider. "PTAT Voltage Generator based on an MOS Voltage Divider". Nanotechnology Conference and Trade Show, Technical Proceedings, 2007.
  4. Andre Luiz Aita and Cesar Ramos Rodrigues. "PTAT CMOS Current Sources Mismatch over Temperature". The 26th Symposium on Integrated Circuits and System Design (SBCCI 2013). 2013.
  • Lua error in package.lua at line 80: module 'strict' not found.

External links