Waldo–Hancock Bridge

Waldo–Hancock Bridge
File:Waldo-Hancock Bridge, Bucksport, ME 1931-2006.jpg Waldo–Hancock Bridge in 2001
Coordinates
Waldo–Hancock Bridge
Formerly listed on the U.S. National Register of Historic Places
Location	US 1, Verona, Maine
Area	4 acres (1.6 ha)
Built	1931
Architect	Robinson & Steinman
Architectural style	Other, Suspension
NRHP Reference #	85001267
Significant dates
Added to NRHP	June 20, 1985
Removed from NRHP	December 18, 2013
Carries	US 1
Crosses	Penobscot River
Locale	Bucksport, Maine, (Hancock County, Maine)
Official name	Waldo–Hancock Bridge
Maintained by	Maine Department of Transportation
ID number	(Bridge No. 2973)
Characteristics
Design	Suspension bridge
Total length	2,040 ft (621.8 m)
Width	20 ft (6.1 m) roadway with Two sidewalks
Height	72 m
Longest span	800 ft (243.8 m)
Clearance below	135 ft (41.1 m)
History
Construction begin	1929
Construction end	1931
Opened	November 16, 1931
Closed	December 30, 2006 (Demolished 2013)
Statistics
Toll	1931–1953

The Waldo–Hancock Bridge was the first long-span suspension bridge erected in Maine, as well as the first permanent bridge across the Penobscot River below Bangor. The name comes from connecting Waldo and Hancock counties. The bridge was retired in 2006, when the new Penobscot Narrows Bridge was opened just a few yards away, and it was demolished in 2013.

The bridge was 2,040 feet (621.8 m) long with a clear center span of 800 feet (243.8 m) between towers. It had two 350-foot (106.7 m) side spans and carries a 20-foot (6.1 m) wide roadway with two sidewalks. It used stiffening trusses that are 9 feet (2.7 m) deep. Each of the main suspender cables were in diameter, and consisted of 37 strands of 37 wires. The deck was 135 feet (41.1 m) above water level to allow passage of large ships. The total cost of the span was less than $850,000 in 1931 dollars (about $12 million in 2010 dollars), significantly under its allocated budget.

Construction

David B. Steinman, of Robinson and Steinman, was the designer. The bridge was fabricated by American Bridge Company (superstructure) and Merritt-Chapman & Scott (substructure).

File:Waldo-Hancock Bridge Dedication Plaque 1931.jpg

Dedication plaque, 1931

Technologically, the Waldo–Hancock Bridge represented a number of firsts. It was one of the first two bridges in the U.S. (along with the St. Johns Bridge in Portland, Oregon, completed in June, 1931) to employ Robinson and Steinman’s prestressed twisted wire strand cables, which were first used on the 1929 Grand Mère Suspension Bridge over the Saint-Maurice River in Quebec. The prefabrication and prestressing of the cables decreased the number of field adjustments required, saving considerable time, effort, and money. As an additional experiment in efficiency, the Waldo–Hancock cables were marked prior to construction, ensuring proper setting. This method had never been used before and proved successful in this instance. These innovations, invented and pioneered by Steinman, were a significant step forward for builders of suspension bridges.

The Waldo–Hancock was also the first bridge to make use of the Vierendeel truss in its two towers, giving it an effect that Steinman called “artistic, emphasizing horizontal and vertical lines.” This attractive and effective truss design was later used in a number of important bridges, including the Triborough Bridge and Golden Gate Bridge.

The Waldo–Hancock Bridge was noted at the time for its economy of design and construction. It cost far less than had been appropriated by the State Highway Commission, which enabled the construction of a second bridge between Verona Island and Bucksport. When opened in 1931 the bridge collected tolls used to retire the bonds issued to finance its construction. All tolls were lifted twenty-two years later on October 31, 1953, however, when those original construction bonds were paid off.

Rehabilitation, replacement and abandonment

As the bridge approached its seventieth anniversary with the end of the century, a series of routine safety inspections made by the Maine Department of Transportation revealed that over those seven decades the structure's two main suspension cables and the many vertical bridge deck stringers had become seriously corroded thereby deteriorating their ability to support the deck, roadway and the traffic that crossed it. These engineering studies made it clear that the bridge required immediate major rehabilitation and eventual replacement.

File:Waldo-Hancock Bridge, Bucksport, ME in July, 2007 after abandonment.jpg

The closed Waldo-Hancock Bridge in 2007 still showing its temporarily repaired cables.

Work was undertaken to rehabilitate the bridge starting in 2000 by Cianbro and Piasecki Steel Construction Corp. with cable work by Williamsport Wirerope Works Inc, by focusing on strengthening the cables. The two cables were done separately, one a time. Piasecki Steel Construction Corp., Castleton, N.Y., rehabilitated the north cable in 2002. At this point the bridge was discovered to be beyond permanent repair and would have to be abandoned and replaced by a new structure to be built adjacent to the aging bridge. Work then shifted to temporary strengthening. For the south cable, MDOT in August 2003 hired Pittsfield, Maine-based Cianbro Corp. under a $4-million emergency contract.

The rehabilitation used a single wire thickness (2-inch (5.1 cm) diameter galvanized helical 91-wire strands.) to facilitate fabricating and installing the cables more quickly. New concrete anchorages with up to 30-foot (9.1 m) long anchor rods were built by Cianbro. Crews installed continuous runs of strands on new saddles bolted and welded on new base plates atop cable bents and the main towers. Workers placed two groups of four strands 12 feet (3.7 m) above each main cable to allow for pulls. Each strand weighs 4 tons (3.6 metric tons). A rope pull was walked across, connected to a pull cable, then winched back across and connected to the strand, which was fed through a tensioner holding back about 15,000 pounds (7,000 kg) to smooth the pull.

“We hooked and rehooked one strand per day on average,” says Archie J. Wheaton, Cianbro project superintendent. “The strands were connected to anchor rods; then we set the sag.” The new auxiliary cables are connected to existing double suspender cables by steel rods, then tensioned with 30-ton (27.2 metric ton) jacks, bringing the new cables about 3 feet (1 m) from the main cables.

A new construction, the Penobscot Narrows Bridge, was built alongside the older one. The new bridge was opened to traffic on December 30, 2006, at which point the Waldo–Hancock Bridge was ceremoniously closed. Barricades were erected at both ends, closing the bridge to both cars and pedestrians.

Demolition

The Maine Department of Transportation announced on February 14, 2012 that the Bridge would be demolished starting that summer and be completed by the fall. The schedule was designed to accommodate the needs of two endangered species, the Peregrine falcon and the Shortnose sturgeon. Barges would be placed in the Penobscot River onto which sections of the bridge would be lowered. The concrete piers in the River would be all that remained, and MDOT worked with the United States Coast Guard to design lights for them once the Bridge was removed to aid ships in the River. Later, MaineDOT announced that the low bid of $5.35 million by S&R Corp. of Lowell, Massachusetts was accepted.

Demolition eventually was delayed until November 20, 2012 with the removal of the bridge's flag poles and was completed in June, 2013.

File:Waldo-Hancock and Penobscot Narrows Bridges 2007 and 2013.jpg

The Waldo-Hancock and Penobscot Narrows Bridges as viewed from the Penobscot Narrows Bridge Observatory in July, 2007, and July, 2013 after the Waldo-Hancock Bridge had been demolished.

Gallery

• LOC historical image of Waldo-Hancock Bridge.tif

  The Waldo–Hancock Bridge, Ft. Knox, and Bucksport, ME seen from Verona Island (1994)

• Waldo-Hancock Bridge, Bucksport, ME 1931-2006.jpg

  The Waldo–Hancock Bridge as seen from the Waldo County approach looking toward Verona Island (2001)

• Waldo-Hancock and Penobscot Narrows Bridges from Ft. Knox July, 2007.jpg

  The Waldo-Hancock and Penobscot Narrows Bridges from Ft. Knox (2007)

• Waldo-Hancock and Penobscot Narrows Bridges entering Verona Island July, 2007.jpg

  The Waldo-Hancock and Penobscot Narrows Bridges entering Verona Island viewed from the west tower observatory (2007)

• Waldo-Hancock and Penobscot Narrows Bridges entering Verona Island July, 2007 (2).jpg

  The Waldo-Hancock and Penobscot Narrows Bridges entering Verona Island viewed from below (2007)

• Waldo-Hancock and Penobscot Narrows Bridges entering Verona Island July, 2007 (3).jpg

  The Waldo-Hancock and Penobscot Narrows Bridges entering Verona Island viewed from below (2007)

Further reading

The following sources referenced in the HAER documentation may be of value:

External links

• Waldo–Hancock Bridge at Structurae — major source of information used in article, although not directly cited.
• Entry at Bridgemeister.com (includes builders plate)
• Entry at Bridgemeister.com (includes distance shots)
• entry on reconstruction at BridgePros.com
• Recabling project from McGraw Hill Engineering News Record site (effort ended up being a temporary stopgap)
• Replacement project at Maine DOT site
• Historic American Engineering Record (HAER) No. ME-65, "Waldo–Hancock Bridge, Spanning Penobscot River at U.S. Route 1, Bucksport vicinity, Hancock, ME"