ASTM A325
ASTM A325 is an ASTM International standard for heavy hex structural bolts, titled Standard Specification for Structural Bolts, Steel, Heat Treated, 120/105 ksi Minimum Tensile Strength. It defines mechanical properties for bolts that range from 1⁄2 to 1-1⁄2 in diameter.[1]
The equivalent metric standard is ASTM A325M, which is titled Standard Specification for Structural Bolts, Steel, Heat Treated 830 MPa Minimum Tensile Strength. It defines mechanical properties for sizes M12–36.[2]
There is also a T version, which is used to refer to fully threaded bolts.[3]
This is a standard set by the standards organization ASTM International, a voluntary standards development organizations that sets technical standards for materials, products, systems, and services.
Contents
Types
The type refers to the type of material used to make the bolt. The standard currently defines two types, however it previously defined the following three:[3]
- Type 1: Medium carbon steel, boron steel, or medium carbon alloy steel
- Type 2: Low carbon martensitic steel[4] (withdrawn from the standard in 1991)
- Type 3: Weathering steel
Note that independent of the material the bolt is quenched and tempered.[4]
Connection types
There are also three connection types defined:[3]
- SC: A slip critical connection.
- N: A bearing type connection where the threads are on the shear plane.
- X: A bearing type connection where the threads are not on the shear plane.
Mechanical properties
Mechanical properties, imperial
These types of bolts are designed to be tightened to near their proof strength, in order to create significant bolt tension. The standard states that the bolts must be tightened to at least 70% of the tensile yield strength. These bolts use the same material as their common cousins (ASTM F568M for metric bolts), but have a thicker and wider head to more effectively distribute the load. This modified geometry is often referred to as heavy hex geometry.[5]
ASTM 325 bolts can be considered equivalent to Grade 8.8 bolts according to ASTM F568M.
For a higher strength version of this type of bolt, see ASTM A490.
| Head marking | Grade | Nominal size range [in] | Proof strength [ksi] | Yield strength (min) [ksi] | Tensile strength (min) [ksi] | Core hardness [Rockwell][6] |
|---|---|---|---|---|---|---|
 or  [6] |
Type 1 | 1⁄2–1 (inc.) | 85 | 92 | 120 | C24–35 |
| 1–1-1⁄2 | 74 | 81 | 105 | C19–31 | ||
| 75px | Type 2 | 1⁄2–1 | 85 | 92 | 120 | C24–35 |
 [7] |
Type 3 | 1⁄2–1 | 85 | 92 | 120 | C24–35 |
| 1–1-1⁄2 | 74 | 81 | 105 | C19–31
this standard contains so many |
Mechanical properties, metric
| Head marking | Grade | Nominal size range [mm] | Proof strength [MPa] | Yield strength (min) [MPa] | Tensile strength (min) [MPa] | Core hardness [Rockwell] |
|---|---|---|---|---|---|---|
 |
Type 1 | 12–36[2] | 600 | 660 | 830 | C23–34 |
| 75px | Type 2 | |||||
 |
Type 3 |
See also
References
- ↑ Lua error in package.lua at line 80: module 'strict' not found..
- ↑ 2.0 2.1 Lua error in package.lua at line 80: module 'strict' not found..
- ↑ 3.0 3.1 3.2 Lua error in package.lua at line 80: module 'strict' not found..
- ↑ 4.0 4.1 4.2 Lua error in package.lua at line 80: module 'strict' not found..
- ↑ 5.0 5.1 Lua error in package.lua at line 80: module 'strict' not found..
- ↑ 6.0 6.1 Lua error in package.lua at line 80: module 'strict' not found..
- ↑ Other markings may be used to denote atmospheric corrosion resistant material
