Balanced-arm lamp

From Infogalactic: the planetary knowledge core
Jump to: navigation, search
Anglepoise model 1227 from 1935

A balanced-arm lamp, sometimes called a floating arm lamp, is a lamp with an adjustable folding arm which is constructed so that the force due to gravity is always counteracted by springs, regardless of the position of the arms of the lamp. Many lamp brands (such as the Anglepoise, originator of the concept, and Luxo L-1) as well as other devices, such as drawing boards, use this principle.

Configuration

Compare human arm.PNG

A balanced-arm lamp has a base, two connected arms fitted with springs, and a lamp-head. The lamp can be moved into any position, and the springs will maintain the position until moved again. The same mechanism can be employed in other devices with similar requirements, such as copy holders for typists and some computer display holders. This article uses the terminology lamp cap, forearm, upper arm and base for the four basic parts of these lamps.

For the physics and theory behind balanced-arm lamps, see Classical mechanics, linkage and torque. There are different methods to balance the lamp-cap of a balanced-arm lamp. Some lamps have two coil springs working in parallel on both sides of the pivoting arm. (A set of springs functions in the same way as a single spring.) Others are balanced with counterweights (a method frequently used in drawing-boards). Friction between parts of the lamp arm can also be used to maintain balance. There are a number of mechanical solutions (coupling, hydraulics and pneumatic arms) which have occasionally been used for balanced-arm lamps.

Lamps balanced with springs

Compression and tension springs at rest and under load

There are many variations of construction with springs. Springs can be located on the mechanical equivalent of the forearm or the upper arm, or both, as well as nearer the base. Some lamps use tension springs, and others use compression springs. The image at the left shows (left to right) a compression spring at rest, then under load, followed by a tension spring at rest, and then under load. Springs have a limited lifting capacity and extension length. Some springs can resonate, producing low-level unwanted noise.

One tension spring

Spring-balanced upper arm, flexible forearm
A flexible forearm

This lamp has a stiff flexible tube as its forearm, and a spring-balanced arm to support it near the middle. That way there is a flexible lamp with a long reach.

Tension spring over wheels
A spring over two wheels

The wheel to control the forearm is smaller than the wheel that controls the upper arm. The lamp cap rotates the same direction as the upper arm and forearm.

Two arms, one spring, one toothed wheel
A single spring controlling upper arm and forearm

With this technique the tension spring has a double function: it controls both the forearm and the upper arm. This is not a common arm lamp system. The lamp cap rotates the same direction as the upper arm and forearm.

Two tension springs

Two parallelograms and two tension spring sets
An upper arm showing three parallel bars

One tension spring controls the forearm, which is a parallelogram having two bars. A stronger spring set controls the upper arm, which has three parallel bars (see photo, left). (There is a less stable construction with two parallel bars in the upper arm which is less expensive to manufacture.) Due to the parallel linkage of the lamp, the lamp cap keeps pointing in the same vertical direction when adjusting the height of the lamp. As with most balanced-arm lamps, the whole assembly can rotate in the horizontal plane, and is mounted on a stable foot.

One parallelogram and two extension spring sets
Anglepoise-style lamp

A lamp like the Anglepoise lamp has one parallelogram and two extension springs. One spring controls the shortest arm of a parallelogram. Parallel to this shortest arm there is the forearm. To keep these arms parallel there are two other parallel arms (upper arm) that are controlled by a second extension spring. The lamp cap rotates the same direction as the upper arm and forearm.

Single forearm bar, one parallelogram, two tension spring sets
Diagram of a single-forearm lamp

The forearm of this lamp consist of a single bar. When it is adjusted, the angle of the lamp cap changes along with the arm.

Tension springs within the arms
Tension springs within the arms

A lamp like the Tolomeo desk lamp has no parallelograms in either arm. In this modern lamp the tension springs are hidden in the arms. The lamp cap rotates the same direction as the upper arm and forearm.

Compression springs

Compression springs in the arms
Compression springs in the arms

The short arms (green) stay parallel. One spring puts pull force on the blue arm. (If the blue arm is tilted back the second spring on this arm gets push force.) The blue arm controls the two parallel arms (red) that make up the upper arm. The other spring puts pull force on the other blue arm. This arm controls the forearm (magenta). The two springs can be the same size; one spring has to lift more weight but is more vertical. The other spring lifts less weight but is more horizontal.

Compression springs near the foot

One compression spring controls a very short arm (grey). The Roller chain cable connects this arm parallel to the forearm (yellow). The longer spring controls the (blue) arm. The body (red) can turn in the horizontal plane. The body is connected to a stable foot. The body can be smaller because the pressure springs can protrude below the body.

A compression spring with one parallelogram
A compression spring with one parallelogram

In this method, just one compression spring controls a pantographic arm.


Lamps balanced by pressure and friction

Pressure and friction lamps
Friction rubber arm
Friction rubber arm
Squeezing rubber arm
The arms are balanced by pressure and friction

This construction is quite common in Italian lamps. Gravity causes the parallelogram to deform, making the gap between the long arms smaller. This increases pressure on the rubber in the gap, and the resulting friction holds the arm in balance.

Lamps balanced with one counterweight

An advantages of one swinging counterbalance is that the lamp can have a longer arm length.

Disadvantages are that the stand is less stable, the lamp needs a heavy foot to stand stable.

A single counterweight
Single weight chain lamp

This construction uses a chain to keep the arm with the counterweight and the forearm parallel. The lamp-cap and counterweight move in opposite directions (both away from the base or both towards it). The balance that is required is shown by the following formula:

d1 = Lamp-cap to base; m1 = weight of lamp-cap
d2 = counterweight to base; m2 = weight of counterweight
m1 × d1 = m2 × d2


One parallelogram with one counterweight
One parallelogram and one counterweight

This lamp has a heavy base, with a parallelogram pantograph construction formed by bars which are all hinged on each other. One long bar extends past the parallelogram construction and has a counterweight. One short bar also extends past the parallelogram construction and holds the lamp cap. The base has an arc formed stand so the counterweight does not hit the stand in vertical position.

One parallelogram with an extended counterweight
Alternative text

This lamp is similar to the one above, but as the counterweight has a low position the lamp needs no heavy foot for stability as the center of gravity is low. The counterbalance does not swing, but slides and rotates safely around the center of the stand.

Three parallelograms with one counterweight
Alternative text

This lamp stand has a complex construction with matching narrow openings. This lamp is out of production .

Lamps balanced with two counterweights

Alternative text
A single arm with two counterweights

With this lamp the movement is very limited (the arm moves up and down only) but the technique is nice to look at. As the forearm becomes more horizontal the weight ceases to be balanced on both side of the base. The weight of the base is needed to avoid over-balancing.

Two arms with two counterweights
Dimension diagram
Dimension diagram
Outer position
Outer position
Lamp with two arms and two counterweights

A lamp type like the Tizio works like this. A balancing arm (the forearm) has on one side of an axis a small counterweight and on the other side a lamp cap. These parts are lifted by a second bigger balancing arm (the upper arm) that has on the other side of a second axis a heavier counterweight. The lamp designed by Edouard-Wilfrid Buquet in 1929 works in this way. The lamp is in the collection of the Museum of Modern Art. The two axes have a different angle, and this has some advantages.

Lamp-cap x fore-Arm = Arm x Small weight (Lamp-cap + Small weight) x upper-arm = Arm x Big weight.

Alt


Lamps using other systems

Here are some less common ways of balancing arms.

Lamps having a vertical axis
Lamps having a vertical axis

This kind of lamp has a forearm balanced by weight or springs. Its disadvantage is that the upper arm cannot point up or forwards.

Friction
Lamp with flexible bars

The friction between the twisted arm controls the movement between the arms.

Another lamp with flexible bars

This arm system also works with friction.

Mechanical coupling devices
Mechanical locking jointlamp

This lamp works by coupling together the upper arm and the forearm. It is called a gravity-locked or cam-locked elbow.[1]

Alt
Hydraulic arm

The biggest pivoting arm lamps in the world are in Rotterdam. They have one hydraulic cylinder to control the forearm, and one hydraulic cylinder to control the upper arm.

Alt
Pneumatic arm

Arm lamp with a pneumatic cylinder. The gravity compress the air in the pneumatic cylinder.

In popular culture

  • Two spring-balanced desk lamps of this type feature as the main characters in the Pixar animated film Luxo Jr.. It also serves as the letter I in the Pixar logo presented before each of their films.
  • Myster Shadow-Sky is the only composer who from 1980 to 2007 performed the Anglepoise Lamp (Anglepoise being a trademark owned by Luxo company, we have now to say "balanced arm lamp") as a musical instrument: the archisonic lamp. In 1980 he wrote the score "Ludus Musicae Temporarium" for a balanced arm lamp orchestra. The world premiere was performed by Les Percussions de Strasbourg at the Manca contemporary music festival in Nice in 1988. He released five albums with a four spring balanced arm lamp musical instrument (and more with other musical instruments). They are available for free download.[2] Referenced in the book "Les chercheurs de sons" (2004), as the unique creator of a balanced arm lamp as a musical instrument.

See also

<templatestyles src="Div col/styles.css"/>

Patents history

Classifications IPC: F21V21/26

International patent category: B23B31/171

  • GB191104491 An Improved Device for Supporting or Suspending Electric Lamps and the like (1911)
  • U.S. Patent 1,370,231 - 1921 harmonica arm
  • [1] 1923 parallelogram & counter weight
  • [2] 1926 friction
  • [3] 1929 2 counter weight
  • [4] 1934 spring and counter weight
  • FR757890 1934 CARWARDINE GEORGE
  • FR784932 1935 CARWARDINE GEORGE
  • [5] 1937 friction
  • [6] 1938 2 parallelogram 2 springs
  • [7] 1939 2 pressure springs
  • [8] 19.. a-symmetric arm-lamp
  • [9] 1947 friction and a spring
  • [10] 1949
  • [11] 1949 spring in the arm
  • [12] 1954 friction arm
  1. U.S. Patent 3,003,737A11,961 -- 1961


References

  1. See here
  2. http://centrebombe.org/myster_shadow-sky_discography.html