Fusion power

From Infogalactic: the planetary knowledge core
Jump to: navigation, search
The Sun is a natural fusion reactor.

Fusion power is the generation of energy by nuclear fusion. Fusion reactions are high energy reactions in which two lighter atomic nuclei fuse to form a heavier nucleus. When they combine, some of the mass is converted into energy in accordance with the formula E=mc^2.[1] This major area of plasma physics research is concerned with harnessing this reaction as a source of large scale sustainable energy.

In large scale commercial proposals, heat from the fusion reaction is used to operate a steam turbine that drives electrical generators, as in existing fossil fuel and nuclear fission power stations. Many different fusion concepts have come in and out of vogue over the years. The current leading designs are the tokamak and inertial confinement fusion (laser) approaches. As of December 2015, these technologies are not yet commercially viable. Currently, it takes more energy to initiate and contain a fusion reaction, than the energy it produces.[2]


Binding energy for different atoms. Iron-56 has the highest, making it the most stable. Atoms to the left are likely to fuse; atoms to the right are likely to split.


Fusion reactions occur when two (or more) atomic nuclei come close enough for the strong nuclear force pulling them together to exceed the electrostatic force pushing them apart, fusing them into heavier nuclei. For nuclei lighter than iron-56, the reaction is exothermic, releasing energy. For nuclei heavier than iron-56, it is endothermic, requiring an external source of energy.[3] Hence, nuclei smaller than iron-56 are more likely to fuse while those heavier than iron-56 are more likely to break apart.

To fuse, nuclei must be brought close enough together for the strong force to act, which occurs only at very short distances. The electrostatic force keeping them apart acts over long distances, so a significant amount of kinetic energy is needed to overcome this "Coulomb barrier" before the reaction can take place. There are several ways of doing this, including speeding up atoms in a particle accelerator, or more commonly, heating them to very high temperatures.

Once an atom is heated above its ionization energy, its electrons are stripped away, leaving just the bare nucleus (the ion). The result is a hot cloud of ions and the electrons formerly attached to them. This cloud is known as a plasma. Because the charges are separated, plasmas are electrically conductive and magnetically controllable. Many fusion devices take advantage of this to control the particles as they are being heated.

Theoretically, any atoms can be fused if enough pressure and temperature are applied,[4] and studies have been made of the conditions required to create fusion conditions for a variety of atoms.[5] Power plants, however, are currently limited to only the lightest elements.[why?] Hydrogen is ideal for this purpose because of its small charge, making it the easiest atom to fuse, and producing helium.

Cross section

The fusion reaction rate increases rapidly with temperature until it maximizes and then gradually drops off. The deuterium-tritium fusion rate peaks at a lower temperature (about 70 keV, or 800 million kelvin) and at a higher value than other reactions commonly considered for fusion energy.

A reaction's cross section, denoted σ, is the measure of how likely a fusion reaction will happen. It is a probability, and it depends on the velocity of the two nuclei when they strike one another. If the atoms move faster, fusion is more likely. If the atoms hit head on, fusion is more likely. Cross sections for many different fusion reactions were measured mainly in the 1970s using particle beams.[5] A beam of ions of material A was fired at material B at different speeds, and the amount of neutrons coming off was measured. Neutrons are a key product of most fusion reactions.

In most cases, the nuclei are flying around in a hot cloud, with some distribution of velocities. If the plasma is thermalized, then the distribution looks like a bell curve, or maxwellian distribution. In this case, it is useful to take the average cross section over the velocity distribution. This is entered into the volumetric fusion rate:[6]

P_\text{fusion} = n_A n_B \langle \sigma v_{A,B} \rangle E_\text{fusion}


  • P_\text{fusion} is the energy made by fusion, per time and volume
  • n is the number density of species A or B, the particles in the volume
  • \langle \sigma v_{A,B} \rangle is the cross section of that reaction, average over all the velocities of the two species v
  • E_\text{fusion} is the energy released by that fusion reaction.

Lawson criterion

This equation shows that energy varies with the temperature, density, speed of collision, and fuel used. This equation was central to John Lawsons' analysis of fusion power plants working with a hot plasma. Lawson assumed an energy balance, shown below.[6]

Net Power = Efficiency * (Fusion - Radiation Loss - Conduction Loss)

  1. Net Power is the net power for any fusion power plant.
  2. Efficiency how much energy is needed to drive the device and how well it collects power.
  3. Fusion is rate of energy generated by the fusion reactions.
  4. Radiation is the energy lost as light, leaving the plasma.
  5. Conduction is the energy lost, as momentum leaves the plasma.

Plasma clouds lose energy through conduction and radiation.[6] Conduction is when ions, electrons or neutrals hit a surface and transfer a portion of their kinetic energy to the atoms of the surface. Radiation is when energy leaves the cloud as light. This can be in the visible, UV, IR or X-Ray light. Radiation increases as the temperature rises. To get net power from fusion, you must overcome these losses.

Triple Product: Density, temperature, time

The Lawson criterion argues that a machine holding in a hot, thermalized and quasi-neutral plasma, has to meet basic criteria to overcome the radiation losses, conduction losses and a power plant efficiency of 30 percent.[6][7] This became known as the "triple product": the plasma density and temperature and how long it is held in.[8] For many years, work has been focused on reaching the highest triple product possible. This emphasis on (n t \tau) as a metric of success, has hurt other considerations like cost, size, complexity and efficiency.[dubious ] This has led to larger, more complicated and more expensive machines like ITER and NIF.[citation needed]

Plasma behavior

Plasma can be made by fully ionizing a gas.[9] Plasma is a fluid which conducts electricity. In bulk, it is modeled using Magnetohydrodynamics which is a combination of the Navier-Stokes equations governing fluids and Maxwell's equations governing how magnetic and electric fields behave.[10] Fusion exploits several plasma properties, including:

Self-Organization Plasma conducts electric and magnetic fields. This means that it can self-organize. Its motions can generate fields which can, in turn, self-contain it.[11]

Diamagnetic Plasma Plasma can generate its own internal magnetic field. This can reject an externally applied magnetic field, making it diagmagnetic.[12]

Magnetic mirrors Plasma can be reflected when it moves from a low to high density magnetic field.[13]

Energy capture

There are several proposals for energy capture. The simplest is using a heat cycle to heat a fluid with fusion reactions. It has been proposed to use the neutrons generated by fusion to re-generate a spent fission fuel.[14] In addition, direct energy conversion, has been developed (at LLNL in the 1980s) as a method to maintain a voltage using the products of a fusion reaction. This has demonstrated an energy capture efficiency of 48 percent.[15]

Possible approaches

Magnetic confinement fusion

Tokamak The most well developed and well funded approach to fusion energy. As of April 2012 there were an estimated 215 tokamaks either planned, decommissioned or currently operating (35 tokamaks), worldwide.[16] This method races hot plasma around in a magnetically confined ring, with an internal current. When completed, ITER will be the world's largest tokamak.

Spherical tokamak A variation on the tokamak with a spherical shape.

Stellarator These are twisted rings of hot plasma. The stellarator attempts to create a natural twist plasma path, using external magnets; while Tokamaks create those magnetic fields using an internal current. Stellarators were developed by Lyman Spitzer in 1950 and have four designs: Torsatron, Heliotron, Heliac and Helias. One such example is Wendelstein 7-X a German reactor that as of December 10, 2015 preformed fusion and sustained it for several seconds

Levitated Dipole Experiment (LDX) These use a solid superconducting torus. This is magnetically levitated inside the reactor chamber. The superconductor forms an axisymmetric magnetic field that contains the plasma. The LDX was developed between MIT and Columbia University after 2000 by Jay Kesner and Michael E. Mauel.[17]

Magnetic mirror Developed by Richard F. Post and teams at LLNL in the 1960s.[18] Magnetic mirrors reflected hot plasma back and forth in a line. Variations included the magnetic bottle and the biconic cusp.[19] A series of well-funded, large, mirror machines were built by the US government in the 1970s and 1980s.

Field-reversed configuration This device traps plasma in a self-organized quasi-stable structure; where the particle motion makes an internal magnetic field which then traps itself.[20]

Reversed field pinch Here the plasma moves inside a ring. It has an internal magnetic field. As you move out from the center of this ring, the magnetic field reverses direction.

Inertial confinement fusion

Direct drive In this technique, lasers directly blast a pellet of fuel. The goal is to start ignition, a fusion chain reaction. Ignition was first suggested by John Nuckolls, in 1972.[21] Notable direct drive experiments have been conducted at the Laboratory for Laser Energetics, Laser Mégajoule and the GEKKO XII facilities. Good implosions require fuel pellets with close to a perfect shape in order to generate a symmetrical inward shock wave and to produce the high-density plasma.

Fast ignition This method uses two laser blasts. The first blast compresses the fusion fuel, while the second high energy pulse ignites it. Experiments have been conducted at the Laboratory for Laser Energetics using the Omega and Omega EP systems and at the GEKKO XII laser at the institute for laser engineering in Osaka Japan.

Indirect drive In this technique, lasers blasts a structure around the pellet of fuel. This structure is known as a Hohlraum. As it disintegrates the pellet is bathed in a more uniform x-ray light, creating better compression. The largest system using this method is the National Ignition Facility.

Magneto-inertial fusion or Magnetized Liner Inertial Fusion This combines a laser pulse with a magnetic pinch. The pinch community refers to it as Magnetized Liner Inertial Fusion while the ICF community refers to it as Magneto-inertial fusion.[22]

Heavy Ion Beams There are also proposal to do inertial confinement fusion with ion beams instead of laser beams.[23] The main difference is the mass of the beam has momentum, whereas lasers do not.

Magnetic or Electric pinches

Z-Pinch This method sends a strong current (in the z-direction) through the plasma. The current generates a magnetic field that squeezes the plasma to fusion conditions. Pinches were the first method for man-made controlled fusion.[24][25] Some examples include the Dense plasma focus and the Z machine at Sandia National Laboratories.

Theta-Pinch This method sends a current inside a plasma, in the theta direction.

Screw Pinch This method combines a theta and z-pinch for improved stabilization.[26]

Inertial electrostatic confinement

Fusor This method uses an electric field to heat ions to fusion conditions. The machine typically uses two spherical cages, a cathode inside the anode, inside a vacuum. These machines are not considered a viable approach to net power due to their high conduction and radiation[27] losses. They are simple enough to build that amateurs have fused atoms using them.[28]

Polywell This designs attempts to combine magnetic confinement with electrostatic fields, to avoid the conduction losses generated by the cage.[29] This research, however, is immature and under developed.[citation needed]


Magnetized target fusion This method confines hot plasma using a magnetic field and squeezes it using inertia. Examples include LANL FRX-L machine,[30] General Fusion and the plasma liner experiment.[31]

Uncontrolled Fusion has been initiated by man, using uncontrolled fission explosions. Early proposals for fusion power included using bombs to initiate reactions.

Beam fusion A beam of high energy particles can be fired at another beam or target and fusion will occur. This was used in the 1970s and 1980s to study the cross sections of high energy fusion reactions.[5]

Bubble fusion This was a supposed fusion reaction that was supposed to occur inside extraordinarily large collapsing gas bubbles, created during acoustic liquid cavitation.[32] This approach was discredited.

Cold fusion This is a hypothetical type of nuclear reaction that would occur at, or near, room temperature. Cold fusion has gained a reputation as Pathological science.[33][34]

Muon-catalyzed fusion Muons allow atoms to get much closer and thus reduce the kinetic energy required to initiate fusion. Muons require more energy to produce than can be obtained from muon-catalysed fusion, making this approach impractical for the generation of power.[35]

Common tools


Gas must be first heated to form a plasma. This then needs to be hot enough to start fusion reactions. A number of heating schemes have been explored:[36]

Radiofrequency Heating A radio wave is applied to the plasma, causing it to oscillate. This is basically the same concept as a microwave oven.

Electrostatic Heating An electric field can do work on charged ions or electrons, heating them.

Neutral Beam Injection An external source of hydrogen is ionized and accelerated by an electric field to form a charged beam which is shone through a source of neutral hydrogen gas towards the plasma which itself is ionized and contained in the reactor by a magnetic field. Some of the intermediate hydrogen gas is accelerated towards the plasma by collisions with the charged beam while remaining neutral: this neutral beam is thus unaffected by the magnetic field and so shines through it into the plasma. Once inside the plasma the neutral beam transmits energy to the plasma by collisions as a result of which it becomes ionized and thus contained by the magnetic field thereby both heating and refuelling the reactor in one operation. The remainder of the charged beam is diverted by magnetic fields onto cooled beam dumps.

Magnetic Oscillations[37]


Thomson Scattering Certain wavelengths of light will scatter off a plasma. This light can be detected and used to reconstruct the plasmas' behavior. This technique can be used to find its density and temperature. It is common in Inertial confinement fusion,[38] Tokamaks[39] and fusors. In ICF systems, this can be done by firing a second beam into a gold foil adjacent to the target. This makes x-rays that scatter or traverse the plasma. In Tokamaks, this can be done using mirrors and detectors to reflect light across a plane (two dimensions) or in a line (one dimension).

Langmuir probe This is a metal object placed in a plasma. A potential is applied to it, giving it a positive or negative voltage against the surrounding plasma. The metal collects charged particles, drawing a current. As the voltage changes, the current changes. This makes a IV Curve. The IV-curve can be used to determine the local plasma density, potential and temperature.[40]

Geiger counter Deuterium or tritium fusion produces neutrons. Geiger counters record the rate of neutron production, so they are an essential tool for demonstrating success.

Flux loop A loop of wire is inserted into the magnetic field. As the field passes through the loop, a current is made. The current is measured and used to find the total magnetic flux through that loop. This has been used on the National Compact Stellarator Experiment,[41] the polywell[42] and the LDX machines.

X-ray detector All plasma loses energy by emitting light. This covers the whole spectrum: visible, IR, UV, and X-rays. This occurs anytime a particle changes speed, for any reason.[43] If the reason is deflection by a magnetic field, the radiation is Cyclotron radiation at low speeds and Synchrotron radiation at high speeds. If the reason is deflection by another particle, plasma radiates X-rays, known as Bremsstrahlung radiation. X-rays are termed in both hard and soft, based on their energy.

Power production

Steam turbines It has been proposed [44] that steam turbines be used to convert the heat from the fusion chamber into electricity. The heat is transferred into a working fluid that turns into steam, driving electric generators.

Neutron blankets Deuterium and tritium fusion generates neutrons. This varies by technique (NIF has a record of 3E14 neutrons per second[45] while a typical fusor produces 1E5 - 1E9 neutrons per second). It has been proposed to use these neutrons as a way to regenerate spent fission fuel [46] or as a way to breed tritium from a liquid lithium blanket.

Direct conversion This is a method where the kinetic energy of a particle is converted into voltage.[47] It was first suggested by Richard F. Post in conjunction with magnetic mirrors, in the late sixties. It has also been suggested for Field-Reversed Configurations. The process takes the plasma, expands it, and converts a large fraction of the random energy of the fusion products into directed motion. The particles are then collected on electrodes at various large electrical potentials. This method has demonstrated an experimental efficiency of 48 percent.[48]


Parameter space occupied by inertial fusion energy and magnetic fusion energy devices as of the mid 1990s. The regime allowing thermonuclear ignition with high gain lies near the upper right corner of the plot.

Confinement refers to all the conditions necessary to keep a plasma dense and hot long enough to undergo fusion. Here are some general principles.

  • Equilibrium: The forces acting on the plasma must be balanced for containment. One exception is inertial confinement, where the relevant physics must occur faster than the disassembly time.
  • Stability: The plasma must be so constructed so that disturbances will not lead to the plasma disassembling.
  • Transport or conduction: The loss of material must be sufficiently slow.[6] The plasma carries off energy with it, so rapid loss of material will disrupt any machines power balance. Material can be lost by transport into different regions or conduction through a solid or liquid.

To produce self-sustaining fusion, the energy released by the reaction (or at least a fraction of it) must be used to heat new reactant nuclei and keep them hot long enough that they also undergo fusion reactions.


The first human-made, large-scale fusion reaction was the test of the hydrogen bomb, Ivy Mike, in 1952. As part of the PACER project, it was once proposed to use hydrogen bombs as a source of power by detonating them in underground caverns and then generating electricity from the heat produced, but such a power plant is unlikely ever to be constructed.

Magnetic confinement

At the temperatures required for fusion, the fuel is heated to a plasma state. In this state it has a very good electrical conductivity. This opens the possibility of confining the plasma with magnetic fields. This is the case of magnetized plasma, where the magnetic fields and plasma intermix. This is generally known as magnetic confinement. The field lines put a Lorentz force on the plasma. The force works perpendicular to the magnetic fields, so one problem in magnetic confinement is preventing the plasma from leaking out the ends of the field lines. A general measure of magnetic trapping in fusion is the beta ratio:

\beta = \frac{p}{p_{mag}} = \frac{n k_B T}{(B^2/2\mu_0)} [49]

This is the ratio of the externally applied field to the internal pressure of the plasma. A value of 1 is ideal trapping. Some examples of beta vales include:

  1. The START machine: 0.32
  2. The Levitated dipole experiment:[50] 0.26
  3. Spheromaks: ≈ 0.1,[51] Maximum 0.2 due to Mercier limit.[52]
  4. The DIII-D machine: 0.126[citation needed]

Magnetic Mirror One example of magnetic confinement is with the magnetic mirror effect. If a particle follows the field line and enters a region of higher field strength, the particles can be reflected. There are several devices that try to use this effect. The most famous was the magnetic mirror machines, which was a series of large, expensive devices built at the Lawrence Livermore National Laboratory from the 1960s to mid 1980s.[53] Some other examples include the magnetic bottles and Biconic cusp.[54] Because the mirror machines were straight, they had some advantages over a ring shape. First, mirrors would easier to construct and maintain and second direct conversion energy capture, was easier to implement.[15] As the confinement achieved in experiments was poor, this approach was abandoned.[citation needed]

Magnetic Loops Another example of magnetic confinement is to bend the field lines back on themselves, either in circles or more commonly in nested toroidal surfaces. The most highly developed system of this type is the tokamak, with the stellarator being next most advanced, followed by the Reversed field pinch. Compact toroids, especially the Field-Reversed Configuration and the spheromak, attempt to combine the advantages of toroidal magnetic surfaces with those of a simply connected (non-toroidal) machine, resulting in a mechanically simpler and smaller confinement area.

Inertial confinement

Inertial confinement is the use of rapidly imploding shell to heat and confine plasma. The shell is imploded using a direct laser blast (direct drive) or a secondary x-ray blast (indirect drive) or heavy ion beams. Theoretically, fusion using lasers would be done using tiny pellets of fuel that explode several times a second. To induce the explosion, the pellet must be compressed to about 30 times solid density with energetic beams. If direct drive is used - the beams are focused directly on the pellet - it can in principle be very efficient, but in practice is difficult to obtain the needed uniformity.[55] The alternative approach, indirect drive, uses beams to heat a shell, and then the shell radiates x-rays, which then implode the pellet. The beams are commonly laser beams, but heavy and light ion beams and electron beams have all been investigated.[56]

Electrostatic confinement

There are also electrostatic confinement fusion devices. These devices confine ions using electrostatic fields. The best known is the Fusor. This device has an cathode inside an anode wire cage. Positive ions fly towards the negative inner cage, and are heated by the electric field in the process. If they miss the inner cage they can collide and fuse. Ions typically hit the cathode, however, creating prohibitory high conduction losses. Also, fusion rates in fusors are very low due to competing physical effects, such as energy loss in the form of light radiation.[57] Designs have been proposed to avoid the problems associated with the cage, by generating the field using a non-neutral cloud. These include a plasma oscillating device,[58] a penning trap and the polywell.[59] The technology is relatively immature, however, and many scientific and engineering questions remain.

History of research


Research into nuclear fusion started in the early part of the 20th century. In 1920 the British physicist Francis William Aston discovered that the total mass equivalent of four hydrogen atoms (two protons and two neutrons) are heavier than the total mass of one helium atom (He-4), which implied that net energy can be released by combining hydrogen atoms together to form helium, and provided the first hints of a mechanism by which stars could produce energy in the quantities being measured. Through the 1920s, Arthur Stanley Eddington became a major proponent of the proton–proton chain reaction (PP reaction) as the primary system running the Sun.


A theory was verified by Hans Bethe in 1939 showing that beta decay and quantum tunneling in the Sun's core might convert one of the protons into a neutron and thereby producing deuterium rather than a diproton. The deuterium would then fuse through other reactions to further increase the energy output. For this work, Bethe won the Nobel Prize in Physics.


In 1942, nuclear fusion research was subsumed into the Manhattan Project and the science became obscured by the secrecy surrounding the field. The first patent related to a fusion reactor was registered in 1946[60] by the United Kingdom Atomic Energy Authority, the inventors being Sir George Paget Thomson and Moses Blackman. This was the first detailed examination of the Z-pinch concept.

Z-pinch is based on the fact that plasmas are electrically conducting. By running a current through the plasma, a magnetic field will be generated around the plasma. This field will, according to Lenz's law, create an inward directed force that causes the plasma to collapse inward, raising its density. Denser plasmas generate denser magnetic fields, increasing the inward force, leading to a chain reaction. If the conditions are correct, this can lead to the densities and temperatures needed for fusion. The difficulty is getting the current into the plasma, which would normally melt any sort of mechanical electrode. A solution emerges again due to the conducting nature of the plasma; by placing the plasma in the middle of an electromagnet, induction can be used to generate the current.

Starting in 1947, small experiments were carried out by two UK teams, who began building a series of ever-larger experiments. When the Huemul results hit the news (see below), James L. Tuck, a UK physicist working at Los Alamos, introduced the pinch concept in the US and produced a series of machines known as the Perhapsatron. In the Soviet Union, unbeknownst to the west, a series of similar machines were being built. All of these devices quickly demonstrated a series of instabilities when the pinch was applied, which broke up the plasma column long before it reached the densities and temperatures required for fusion.


The first man-made device to achieve ignition was the detonation of this fission device, codenamed Ivy Mike.
Early photo of plasma inside a pinch machine (imperial college 1950/1951)

The first successful man-made fusion device was the boosted fission weapon tested in 1951 in the Greenhouse Item test. This was followed by true fusion weapons in 1952's Ivy Mike, and the first practical examples in 1954's Castle Bravo. This was uncontrolled fusion. In these devices, the energy released by the fission explosion is used to compress and heat fusion fuel, starting a fusion reaction. Fusion releases neutrons. These neutrons hit the surrounding fission fuel, causing the atoms to split apart much faster than normal fission processes - almost instantly by comparison. This increases the effectiveness of bombs: normal fission weapons blow themselves apart before all their fuel is used; fusion/fission weapons do not have this practical upper limit.

In 1949 an expatriate German, Ronald Richter, proposed the Huemul Project in Argentina, announcing positive results in 1951. These turned out to be fake, but it prompted considerable interest in the concept as a whole. In particular, it prompted Lyman Spitzer to begin considering ways to solve some of the more obvious problems involved in confining a hot plasma, and, unaware of the z-pinch efforts, he developed a new solution to the problem known as the stellarator. Spitzer applied to the US Atomic Energy Commission for funding to build a test device. During this period, Jim Tuck who had worked with the UK teams had been introducing the z-pinch concept to his coworkers at his new job at Los Alamos National Laboratory (LANL). When he heard of Spitzer's pitch for funding, he applied to build a machine of his own, the Perhapsatron.

Spitzer's idea won funding and he began work on the stellarator under the code name Project Matterhorn. His work led to the creation of the Princeton Plasma Physics Laboratory. Tuck returned to LANL and arranged local funding to build his machine. By this time, however, it was clear that all of the pinch machines were suffering from the same issues involving stability, and progress stalled. In 1953, Tuck and others suggested a number of solutions to the stability problems. This led to the design of a second series of pinch machines, led by the UK ZETA and Sceptre devices.

Spitzer had planned an aggressive development project of four machines, A, B, C, and D. A and B were small research devices, C would be the prototype of a power-producing machine, and D would be the prototype of a commercial device. A worked without issue, but even by the time B was being used it was clear the stellarator was also suffering from instabilities and plasma leakage. Progress on C slowed as attempts were made to correct for these problems.

By the mid-1950s it was clear that the simple theoretical tools being used to calculate the performance of all fusion machines were simply not predicting their actual behavior. Machines invariably leaked their plasma from their confinement area at rates far higher than predicted. In 1954, Edward Teller held a gathering of fusion researchers at the Princeton Gun Club, near the Project Matterhorn (now known as Project Sherwood) grounds. Teller started by pointing out the problems that everyone was having, and suggested that any system where the plasma was confined within concave fields was doomed to fail. Attendees remember him saying something to the effect that the fields were like rubber bands, and they would attempt to snap back to a straight configuration whenever the power was increased, ejecting the plasma. He went on to say that it appeared the only way to confine the plasma in a stable configuration would be to use convex fields, a "cusp" configuration.[61]

When the meeting concluded, most of the researchers quickly turned out papers saying why Teller's concerns did not apply to their particular device. The pinch machines did not use magnetic fields in this way at all, while the mirror and stellarator seemed to have various ways out. This was soon followed by a paper by Martin David Kruskal and Martin Schwarzschild discussing pinch machines, however, which demonstrated instabilities in those devices were inherent to the design.

The largest "classic" pinch device was the ZETA, including all of these suggested upgrades, starting operations in the UK in 1957. In early 1958, John Cockcroft announced that fusion had been achieved in the ZETA, an announcement that made headlines around the world. When physicists in the US expressed concerns about the claims they were initially dismissed. US experiments soon demonstrated the same neutrons, although temperature measurements suggested these could not be from fusion reactions. The neutrons seen in the UK were later demonstrated to be from different versions of the same instability processes that plagued earlier machines. Cockcroft was forced to retract the fusion claims, and the entire field was tainted for years. ZETA ended its experiments in 1968.

The first controlled fusion experiment was accomplished using Scylla I at the Los Alamos National Laboratory in 1958. This was a pinch machine, with a cylinder full of deuterium. Electric current shot down the sides of the cylinder. The current made magnetic fields that compressed the plasma to 15 million degrees Celsius, squeezed the gas, fused it and produced neutrons.[24][25]

In 1950–1951 I.E. Tamm and A.D. Sakharov in the Soviet Union, first discussed a tokamak-like approach. Experimental research on those designs began in 1956 at the Kurchatov Institute in Moscow by a group of Soviet scientists led by Lev Artsimovich. The tokamak essentially combined a low-power pinch device with a low-power simple stellarator. The key was to combine the fields in such a way that the particles orbited within the reactor a particular number of times, today known as the "safety factor". The combination of these fields dramatically improved confinement times and densities, resulting in huge improvements over existing devices.


A key plasma physics text was published by Lyman Spitzer at Princeton in 1963.[62] Spitzer took the ideal gas laws and adopted them to an ionized plasma, developing many of the fundamental equations used to model a plasma.

Laser fusion was suggested in 1962 by scientists at Lawrence Livermore National Laboratory, shortly after the invention of the laser itself in 1960. At the time, Lasers were low power machines, but low-level research began as early as 1965. Laser fusion, formally known as inertial confinement fusion, involves imploding a target by using laser beams. There are two ways to do this: indirect drive and direct drive. In direct drive, the laser blasts a pellet of fuel. In indirect drive, the lasers blast a structure around the fuel. This makes x-rays that squeeze the fuel. Both methods compress the fuel so that fusion can take place.

At the 1964 World's Fair, the public was given its first demonstration of nuclear fusion.[63] The device was a θ-pinch from General Electric. This was similar to the Scylla machine developed earlier at Los Alamos.

The magnetic mirror was first published in 1967 by Richard F. Post and many others at the Lawrence Livermore National Laboratory.[18] The mirror consisted of two large magnets arranged so they had strong fields within them, and a weaker, but connected, field between them. Plasma introduced in the area between the two magnets would "bounce back" from the stronger fields in the middle.

The A.D. Sakharov group constructed the first tokamaks, the most successful being the T-3 and its larger version T-4. T-4 was tested in 1968 in Novosibirsk, producing the world's first quasistationary fusion reaction.[64] When this were first announced, the international community was highly skeptical. A British team was invited to see T-3, however, and after measuring it in depth they released their results that confirmed the Soviet claims. A burst of activity followed as many planned devices were abandoned and new tokamaks were introduced in their place — the C model stellarator, then under construction after many redesigns, was quickly converted to the Symmetrical Tokamak.

In his work with vacuum tubes, Philo Farnsworth observed that electric charge would accumulate in regions of the tube. Today, this effect is known as the Multipactor effect.[65] Farnsworth reasoned that if ions were concentrated high enough they could collide and fuse. In 1962, he filed a patent on a design using a positive inner cage to concentrate plasma, in order to achieve nuclear fusion.[66] During this time, Robert L. Hirsch joined the Farnsworth Television labs and began work on what became the fusor. Hirsch patented the design in 1966[67] and published the design in 1967.[68]


Shiva laser, 1977, the largest ICF laser system built in the seventies
The Tandem Mirror Experiment (TMX) in 1979

In 1972, John Nuckolls outlined the idea of ignition.[21] This is a fusion chain reaction. Hot helium made during fusion reheats the fuel and starts more reactions. John argued that ignition would require lasers of about 1 kJ. This turned out to be wrong. Nuckolls's paper started a major development effort. Several laser systems were built at LLNL. These included the argus, the Cyclops, the Janus, the long path, the Shiva laser and the Nova in 1984. This prompted the UK to build the Central Laser Facility in 1976.[69]

During this time, great strides in understanding the tokamak system were made. A number of improvements to the design are now part of the "advanced tokamak" concept, which includes non-circular plasma, internal diverters and limiters, often superconducting magnets, and operate in the so-called "H-mode" island of increased stability. Two other designs have also become fairly well studied; the compact tokamak is wired with the magnets on the inside of the vacuum chamber, while the spherical tokamak reduces its cross section as much as possible.

In 1974 a study of the ZETA results demonstrated an interesting side-effect; after an experimental run ended, the plasma would enter a short period of stability. This led to the reversed field pinch concept, which has seen some level of development since. On May 1, 1974, the KMS fusion company (founded by Kip Siegel) achieves the world's first laser induced fusion in a deuterium-tritium pellet.[70]

In the mid-1970s, Project PACER, carried out at Los Alamos National Laboratory (LANL) explored the possibility of a fusion power system that would involve exploding small hydrogen bombs (fusion bombs) inside an underground cavity.[71] As an energy source, the system is the only fusion power system that could be demonstrated to work using existing technology. It would also require a large, continuous supply of nuclear bombs, however, making the economics of such a system rather questionable.

In 1976, the two beam Argus laser becomes operational at livermore[citation needed]. In 1977, The 20 beam Shiva laser at Livermore is completed, capable of delivering 10.2 kilojoules of infrared energy on target. At a price of $25 million and a size approaching that of a football field, Shiva is the first of the megalasers[citation needed]. That same year, the JET project is approved by the European Commission and a site is selected.


Magnetic mirrors suffered from end losses, requiring high power, complex magnetic designs, such as the baseball coil pictured here.
The magnetic mirror test facility during construction
The Novette target chamber (metal sphere with diagnostic devices sticking out), which was reused from the Shiva project and two newly built laser chains visible in background.
Inertial confinement fusion implosion on the Nova laser during the 1980s was a key driver of fusion development.

As a result of advocacy, the cold war, and the 1970s energy crisis a massive magnetic mirror program was funded by the US federal government in the late 1970s and early 1980s. This program resulted in a series of large magnetic mirror devices including: 2X,[72] Baseball I, Baseball II, the Tandem Mirror Experiment, the Tandem mirror experiment upgrade, the Mirror Fusion Test Facility and the MFTF-B. These machines were built and tested at Livermore from the late 1960s to the mid 1980s.[73][74] A number of institutions collaborated on these machines, conducting experiments. These included the Institute for Advanced Study and the University of Wisconsin–Madison. The last machine, the Mirror Fusion Test Facility cost 372 million dollars and was, at that time, the most expensive project in Livermore history.[75] It opened on February 21, 1986 and was promptly shut down. The reason given was to balance the United States federal budget. This program was supported from within the Carter and early Reagan administrations by Edwin E. Kintner, a US Navy captain, under Alvin Trivelpiece.[76]

In Laser fusion progressed: in 1983, the NOVETTE laser was completed. The following December 1984, the ten beam NOVA laser was finished. Five years later, NOVA would produce a maximum of 120 kilojoules of infrared light, during a nanosecond pulse[citation needed]. Meanwhile, efforts focused on either fast delivery or beam smoothness. Both tried to deliver the energy uniformly to implode the target. One early problem was that the light in the infrared wavelength, lost lots of energy before hitting the fuel. Breakthroughs were made at the Laboratory for Laser Energetics at the University of Rochester. Rochester scientists used frequency-tripling crystals to transform the infrared laser beams into ultraviolet beams. In 1985, Donna Strickland[77] and Gérard Mourou invented a method to amplify lasers pulses by "chirping". This method changes a single wavelength into a full spectrum. The system then amplifies the laser at each wavelength and then reconstitutes the beam into one color. Chirp pulsed amplification became instrumental in building the National Ignition Facility and the Omega EP system. Most research into ICF was towards weapons research, because the implosion is relevant to nuclear weapons.

During this time Los Alamos National Laboratory constructed a series of laser facilities.[78] This included Gemini (a two beam system), Helios (eight beams), Antares (24 beams) and Aurora (96 beams).[79][80] The program ended in the early nineties with a cost on the order of one billion dollars.[78]

In 1987, Akira Hasegawa [81] noticed that in a dipolar magnetic field, fluctuations tended compress the plasma without energy loss. This effect was noticed in data taken by Voyager 2, when it encountered Uranus. This observation would become the basis for a fusion approach known as the Levitated dipole.

In Tokamaks, the Tore Supra was under construction over the middle of the eighties (1983 to 1988). This was a Tokamak built in Cadarache, France.[82] In 1983, the JET was completed and first plasmas achieved. In 1985, the Japanese tokamak, JT-60 was completed. In 1988, the T-15 a Soviet tokamak was completed. It was the first industrial fusion reactor to use superconducting magnets to control the plasma. These were Helium cooled.

In 1989, Pons and Fleischmann submitted papers to the Journal of Electroanalytical Chemistry claiming that they had observed fusion in a room temperature device and disclosing their work in a press release.[83] Some scientists reported excess heat, neutrons, tritium, helium and other nuclear effects in so-called cold fusion systems, which for a time gained interest as showing promise. Hopes fell when replication failures were weighed in view of several reasons cold fusion is not likely to occur, the discovery of possible sources of experimental error, and finally the discovery that Fleischmann and Pons had not actually detected nuclear reaction byproducts.[84] By late 1989, most scientists considered cold fusion claims dead,[85] and cold fusion subsequently gained a reputation as pathological science.[86] However, a small community of researchers continues to investigate cold fusion[85][87][88][89] claiming to replicate Fleishmann and Pons' results including nuclear reaction byproducts.[90][91] Claims related to cold fusion are largely disbelieved in the mainstream scientific community.[92] In 1989, the majority of a review panel organized by the US Department of Energy (DOE) found that the evidence for the discovery of a new nuclear process was not persuasive. A second DOE review, convened in 2004 to look at new research, reached conclusions similar to the first.[93]

In 1984, Martin Peng of ORNL proposed[94] an alternate arrangement of the magnet coils that would greatly reduce the aspect ratio while avoiding the erosion issues of the compact tokamak: a Spherical tokamak. Instead of wiring each magnet coil separately, he proposed using a single large conductor in the center, and wiring the magnets as half-rings off of this conductor. What was once a series of individual rings passing through the hole in the center of the reactor was reduced to a single post, allowing for aspect ratios as low as 1.2.[95][96] The ST concept appeared to represent an enormous advance in tokamak design. However, it was being proposed during a period when US fusion research budgets were being dramatically scaled back. ORNL was provided with funds to develop a suitable central column built out of a high-strength copper alloy called "Glidcop". However, they were unable to secure funding to build a demonstration machine, "STX". Failing to build an ST at ORNL, Peng began a worldwide effort to interest other teams in the ST concept and get a test machine built. One way to do this quickly would be to convert a spheromak machine to the Spherical tokamak layout.[96] Peng's advocacy also caught the interest of Derek Robinson, of the United Kingdom Atomic Energy Authority fusion center at Culham. Robinson was able to gather together a team and secure funding on the order of 100,000 pounds to build an experimental machine, the Small Tight Aspect Ratio Tokamak, or START. Several parts of the machine were recycled from earlier projects, while others were loaned from other labs, including a 40 keV neutral beam injector from ORNL. Construction of START began in 1990, it was assembled rapidly and started operation in January 1991.[97]


Z Machine (a pinch at SNL) went through a number of upgrades during the mid to late nineties
Mockup of a gold-plated hohlraum designed for use in the National Ignition Facility

In 1991 the Preliminary Tritium Experiment at the Joint European Torus in England achieved the world’s first controlled release of fusion power.[98]

In 1992, a major article was published in Physics Today by Robert McCory at the Laboratory for laser energetics outlying the current state of ICF and advocating for a national ignition facility.[99] This was followed up by a major review article, from John Lindl in 1995,[100] advocating for NIF. During this time a number of ICF subsystems were developing, including target manufacturing, cryogenic handling systems, new laser designs (notably the NIKE laser at NRL) and improved diagnostics like time of flight analyzers and Thomson scattering. This work was done at the NOVA laser system, General Atomics, Laser Mégajoule and the GEKKO XII system in Japan. Through this work and lobbying by groups like the fusion power associates and John Sethian at NRL, a vote was made in congress, authorizing funding for the NIF project in the late nineties.

In the early nineties, theory and experimental work regarding fusors and polywells was published.[101][102] In response, Todd Rider at MIT developed general models of these devices.[103] Rider argued that all plasma systems at thermodynamic equilibrium were fundamentally limited. In 1995, William Nevins published a criticism [104] arguing that the particles inside fusors and polywells would build up angular momentum, causing the dense core to degrade.

In 1995, the University of Wisconsin–Madison built a large fusor, known as HOMER, which is still in operation.[105] Meanwhile, Dr George H. Miley at Illinois, built a small fusor that has produced neutrons using deuterium gas [106] and discovered the "star mode" of fusor operation.[107] The following year, the first "US-Japan Workshop on IEC Fusion", was conducted. At this time in Europe, an IEC device was developed as a commercial neutron source by Daimler-Chrysler and NSD Fusion.[108][109]

In 1996, the Z-machine was upgraded and opened to the public by the US Army in August 1998 in Scientific American.[110][111] The key attributes of Sandia’s Z machine[112] are its 18 million amperes and a discharge time of less than 100 nanoseconds. This generates a magnetic pulse, inside a large oil tank, this strikes an array of tungsten wires called a liner.[113] Firing the Z-machine has become a way to test very high energy, high temperature (2 billion degrees) conditions.[114] In 1996, the Tore Supra creates a plasma for two minutes with a current of almost 1 million amperes driven non-inductively by 2.3 MW of lower hybrid frequency waves. This is 280 MJ of injected and extracted energy. This result was possible due to the actively cooled plasma-facing components[citation needed]

In 1997, JET produced a peak of 16.1MW of fusion power (65% of input power), with fusion power of over 10MW sustained for over 0.5 sec. Its successor, the International Thermonuclear Experimental Reactor (ITER), was officially announced as part of a seven-party consortium (six countries and the EU).[115] ITER is designed to produce ten times more fusion power than the power put into the plasma. ITER is currently under construction in Cadarache, France.

In the late nineties, a team at Columbia University and MIT developed the Levitated dipole a fusion device which consisted of a superconducting electromagnet, floating in a saucer shaped vacuum chamber. Plasma swirled around this donut and fused along the center axis.


Starting in 1999, a growing number of amateurs have been able to fuse atoms using homemade fusors, shown here.[116][117][118][119][120]
A view inside the Levitated dipole experiment.
The Mega Ampere Spherical Tokamak became operational in the UK in 1999

In the March 8, 2002 issue of the peer-reviewed journal Science, Rusi P. Taleyarkhan and colleagues at the Oak Ridge National Laboratory (ORNL) reported that acoustic cavitation experiments conducted with deuterated acetone (C3D6O) showed measurements of tritium and neutron output consistent with the occurrence of fusion.[121] Taleyarkhan was later found guilty of misconduct,[122] the Office of Naval Research debarred him for 28 months from receiving Federal Funding,[123][124] and his name was listed in the 'Excluded Parties List'.[123]

"Fast ignition" was developed in the late nineties, and was part of a push by the Laboratory for Laser Energetics for building the Omega EP system. This system was finished in 2008. Fast ignition showed such dramatic power savings that ICF appears to be a useful technique for energy production. There are even proposals to build an experimental facility dedicated to the fast ignition approach, known as HiPER.

In April 2005, a team from UCLA announced[125] it had devised a way of producing fusion using a machine that "fits on a lab bench", using lithium tantalate to generate enough voltage to smash deuterium atoms together. The process, however, does not generate net power (see Pyroelectric fusion). Such a device would be useful in the same sort of roles as the fusor. In 2006, China's EAST test reactor is completed. This was the first tokamak to use superconducting magnets to generate both the toroidal and poloidal fields.

In the early 2000s, Researchers at LANL reasoned that a plasma oscillating could be at local thermodynamic equilibrium. This prompted the POPS and Penning trap designs.[126][127] At this time, researchers at MIT became interested in fusors for space propulsion[128] and powering space vehicles.[129] Specifically, researchers developed fusors with multiple inner cages. Greg Piefer graduated from Madison and founded Phoenix Nuclear Labs, a company that developed the fusor into a neutron source for the mass production of medical isotopes.[130] Robert Bussard began speaking openly about the Polywell in 2006.[131] He attempted to generate interest[132] in the research, before his death. In 2008, Taylor Wilson achieved notoriety[133][134] for achieving nuclear fusion at 14, with a homemade fusor.[135][136][137]

In 2009, a high-energy laser system, the National Ignition Facility (NIF), was finished in the US, which can heat hydrogen atoms to temperatures only existing in nature in the cores of stars. The new laser is expected to have the ability to produce, for the first time, more energy from controlled, inertially confined nuclear fusion than was required to initiate the reaction.[138]


The preamplifiers of the National Ignition Facility. In 2012 NIF achieved a 500-terawatt shot.

In 2010, NIF researchers were conducting a series of "tuning" shots to determine the optimal target design and laser parameters for high-energy ignition experiments with fusion fuel in the following months.[139] Two firing tests were performed on October 31, 2010 and November 2, 2010. In early 2012, NIF director Mike Dunne expected the laser system to generate fusion with net energy gain by the end of 2012.[140] However, due to delays, it was not achieved by that date.

Inertial (laser) confinement is being developed at the United States National Ignition Facility (NIF) based at Lawrence Livermore National Laboratory in California, the French Laser Mégajoule, and the planned European Union High Power laser Energy Research (HiPER) facility. NIF reached initial operational status in 2010 and has been in the process of increasing the power and energy of its "shots", with fusion ignition tests to follow.[141] A three-year goal announced in 2009 to produce net energy from fusion by 2012 was missed; in September 2013, however, the facility announced a significant milestone from an August 2013 test that produced more energy from the fusion reaction than had been provided to the fuel pellet. This was reported as the first time this had been accomplished in fusion power research. The facility reported that their next step involved improving the system to prevent the hohlraum from either breaking up asymmetrically or too soon.[142][143][144]

A 2012 paper demonstrated that a dense plasma focus had achieved temperatures of 1.8 billion degrees Celsius, sufficient for boron fusion, and that fusion reactions were occurring primarily within the contained plasmoid, a necessary condition for net power.[145] The focus consists of two coaxial cylindrical electrodes made from copper or beryllium and housed in a vacuum chamber containing a low-pressure fusible gas. An electrical pulse is applied across the electrodes, heating the gas into a plasma. The current forms into a minuscule vortex along the axis of the machine, which then kinks into a cage of current with an associated magnetic field. The cage of current and magnetic-field-entrapped plasma is called a plasmoid. The acceleration of the electrons about the magnetic field lines heats the nuclei within the plasmoid to fusion temperatures.

In April 2014, Lawrence Livermore National Laboratory ended the Laser Inertial Fusion Energy (LIFE) program and redirected their efforts towards NIF.[146] In August 2014, Phoenix Nuclear Labs announced the sale of a high-yield neutron generator that could sustain 5×1011 deuterium fusion reactions per second over a 24-hour period.[147] In October 2014, Lockheed Martin's Skunk Works announced the development of a high-beta fusion reactor that they hope to yield a functioning 100-megawatt prototype by 2017 and to be ready for regular operation by 2022.[148][149][150] Deep-space exploration as well as higher-velocity lower-cost space transport services in general would be enabled by this compact fusion reactor technology.[151]

In January 2015, the polywell was presented at Microsoft Research.[152]

In August, 2015, MIT announced a tokamak it named ARC fusion reactor design using rare-earth barium-copper oxide (REBCO) superconducting tapes to produce high-magnetic field coils that it claimed produce comparable magnetic field strength in a smaller configuration than other designs.[153]

In October, 2015, researchers at the Max Planck Institute of Plasma Physics completed building the largest stellarator to date, named Wendelstein 7-X.


By firing particle beams at targets, many fusion reactions have been tested, while the fuels considered for power have all been light elements like the isotopes of hydrogen—deuterium and tritium.[5] Other reactions like the deuterium and Helium3 reaction or the Helium3 and Helium3 reactions, would require a supply of Helium3. This can either come from other nuclear reactions or from extraterrestrial sources. Finally, researchers hope to do the p-11B reaction, because it does not directly produce neutrons, though side reactions can.[154]

Deuterium, tritium

Diagram of the D-T reaction

The easiest nuclear reaction, at the lowest energy, is:

+ 3
+ 1

This reaction is common in research, industrial and military applications, usually as a convenient source of neutrons. Deuterium is a naturally occurring isotope of hydrogen and is commonly available. The large mass ratio of the hydrogen isotopes makes their separation easy compared to the difficult uranium enrichment process. Tritium is a natural isotope of hydrogen, but due to its short half-life of 12.32 years, is hard to find, store, produce, and is expensive. Consequently, the deuterium-tritium fuel cycle requires the breeding of tritium from lithium using one of the following reactions:

+ 6
+ 4
+ 7
+ 4
+ 1

The reactant neutron is supplied by the D-T fusion reaction shown above, and the one that has the greatest yield of energy. The reaction with 6Li is exothermic, providing a small energy gain for the reactor. The reaction with 7Li is endothermic but does not consume the neutron. At least some 7Li reactions are required to replace the neutrons lost to absorption by other elements. Most reactor designs use the naturally occurring mix of lithium isotopes.

Several drawbacks are commonly attributed to D-T fusion power:

  1. It produces substantial amounts of neutrons that result in the neutron activation of the reactor materials.[155]
  2. Only about 20% of the fusion energy yield appears in the form of charged particles with the remainder carried off by neutrons, which limits the extent to which direct energy conversion techniques might be applied.[156]
  3. It requires the handling of the radioisotope tritium. Similar to hydrogen, tritium is difficult to contain and may leak from reactors in some quantity. Some estimates suggest that this would represent a fairly large environmental release of radioactivity.[157]

The neutron flux expected in a commercial D-T fusion reactor is about 100 times that of current fission power reactors, posing problems for material design. After a series of D-T tests at JET, the vacuum vessel was sufficiently radioactive that remote handling was required for the year following the tests.[158]

In a production setting, the neutrons would be used to react with lithium in order to create more tritium. This also deposits the energy of the neutrons in the lithium, which would then be transferred to drive electrical production. The lithium neutron absorption reaction protects the outer portions of the reactor from the neutron flux. Newer designs, the advanced tokamak in particular, also use lithium inside the reactor core as a key element of the design. The plasma interacts directly with the lithium, preventing a problem known as "recycling". The advantage of this design was demonstrated in the Lithium Tokamak Experiment.


Deuterium fusion cross section (in cubic meters) at different ion collision energies.

This is the second easiest fusion reaction, fusing deuterium with itself. The reaction has two branches that occur with nearly equal probability:

D + D → T + 1H
D + D 3He + n

This reaction is also common in research. The optimum energy to initiate this reaction is 15 keV, only slightly higher than the optimum for the D-T reaction. The first branch does not produce neutrons, but it does produce tritium, so that a D-D reactor will not be completely tritium-free, even though it does not require an input of tritium or lithium. Unless the tritons can be quickly removed, most of the tritium produced would be burned before leaving the reactor, which would reduce the handling of tritium, but would produce more neutrons, some of which are very energetic. The neutron from the second branch has an energy of only 2.45 MeV (0.393 pJ), whereas the neutron from the D-T reaction has an energy of 14.1 MeV (2.26 pJ), resulting in a wider range of isotope production and material damage. When the tritons are removed quickly while allowing the 3He to react, the fuel cycle is called "tritium suppressed fusion"[159] The removed tritium decays to 3He with a 12.5 year half life. By recycling the 3He produced from the decay of tritium back into the fusion reactor, the fusion reactor does not require materials resistant to fast 14.1 MeV (2.26 pJ) neutrons.

Assuming complete tritium burn-up, the reduction in the fraction of fusion energy carried by neutrons would be only about 18%, so that the primary advantage of the D-D fuel cycle is that tritium breeding would not be required. Other advantages are independence from scarce[dubious ] lithium resources and a somewhat softer neutron spectrum. The disadvantage of D-D compared to D-T is that the energy confinement time (at a given pressure) must be 30 times longer and the power produced (at a given pressure and volume) would be 68 times less[citation needed] .

Assuming complete removal of tritium and recycling of 3He, only 6% of the fusion energy is carried by neutrons. The tritium-suppressed D-D fusion requires an energy confinement that is 10 times longer compared to D-T and a plasma temperature that is twice as high.[160]

Deuterium, helium 3

A second-generation approach to controlled fusion power involves combining helium-3 (3He) and deuterium (2H):

D + 3He 4He + 1H

This reaction produces a helium-4 nucleus (4He) and a high-energy proton. As with the p-11B aneutronic fusion fuel cycle, most of the reaction energy is released as charged particles, reducing activation of the reactor housing and potentially allowing more efficient energy harvesting (via any of several speculative technologies).[citation needed] In practice, D-D side reactions produce a significant number of neutrons, resulting in p-11B being the preferred cycle for aneutronic fusion.

Proton, boron 11

If aneutronic fusion is the goal, then the most promising candidate may be the Hydrogen-1 (proton)/boron reaction, which releases alpha (helium) particles, but does not rely on neutron scattering for energy transfer.

1H + 11B → 3 4He

Under reasonable assumptions, side reactions will result in about 0.1% of the fusion power being carried by neutrons.[161] At 123 keV, the optimum temperature for this reaction is nearly ten times higher than that for the pure hydrogen reactions, the energy confinement must be 500 times better than that required for the D-T reaction, and the power density will be 2500 times lower than for D-T.

Because the confinement properties of conventional approaches to fusion such as the tokamak and laser pellet fusion are marginal, most proposals for aneutronic fusion are based on radically different confinement concepts, such as the Polywell and the Dense Plasma Focus. Results have been extremely promising:

"In the October 2013 edition of Nature Communications,[162] a research team led by Christine Labaune at Ecole Polytechnique in Palaiseau, France, reported a new record fusion rate: an estimated 80 million fusion reactions during the 1.5 nanoseconds that the laser fired, which is at least 100 times more than any previous proton-boron experiment. " [7]

Material selection


Any power plant using hot plasma, is going to have plasma facing walls. In even the simplest plasma approaches, the material will get blasted with matter and energy. This leads to a minimum list of considerations, including dealing with:

Depending on the approach, these effects may be higher or lower than typical fission reactors like the pressurized water reactor (PWR).[163] One estimate put the radiation at 100 times the (PWR)[citation needed]. Materials need to be selected or developed that can withstand these basic conditions.[164][165] Depending on the approach, however, there may be other considerations such as electrical conductivity, magnetic permeability and mechanical strength. There is also a need for materials whose primary components and impurities do not result in long-lived radioactive wastes.


For long term use, each atom in the wall is expected to be hit by a neutron and displaced about a hundred times before the material is replaced. High-energy neutrons will produce hydrogen and helium by way of various nuclear reactions that tends to form bubbles at grain boundaries and result in swelling, blistering or embrittlement.[163]


One can choose either a low-Z material, such as graphite or beryllium, or a high-Z material, usually tungsten with molybdenum as a second choice. Use of liquid metals (lithium, gallium, tin) has also been proposed, e.g., by injection of 1–5 mm thick streams flowing at 10 m/s on solid substrates[citation needed].

If graphite is used, the gross erosion rates due to physical and chemical sputtering would be many meters per year, so one must rely on redeposition of the sputtered material. The location of the redeposition will not exactly coincide with the location of the sputtering, so one is still left with erosion rates that may be prohibitive. An even larger problem is the tritium co-deposited with the redeposited graphite. The tritium inventory in graphite layers and dust in a reactor could quickly build up to many kilograms, representing a waste of resources and a serious radiological hazard in case of an accident. The consensus of the fusion community seems to be that graphite, although a very attractive material for fusion experiments, cannot be the primary PFC material in a commercial reactor.

The sputtering rate of tungsten by the plasma fuel ions is orders of magnitude smaller than that of carbon, and tritium is much less incorporated into redeposited tungsten, making this a more attractive choice. On the other hand, tungsten impurities in a plasma are much more damaging than carbon impurities, and self-sputtering of tungsten can be high, so it will be necessary to ensure that the plasma in contact with the tungsten is not too hot (a few tens of eV rather than hundreds of eV). Tungsten also has disadvantages in terms of eddy currents and melting in off-normal events, as well as some radiological issues.

Safety and the environment

Accident potential

Catastrophic accidents that release radioactivity to the environment or injury to non-staff are not possible, unlike fission reactors. Nuclear fusion is very unlike nuclear fission: fusion requires extremely precise and controlled temperature, pressure and magnetic field parameters for any net energy to be produced along with a far smaller amount of fuel. If a reactor suffers damage or loses even a small degree of required control, fusion reactions and heat generation would rapidly cease.[166] Therefore, fusion reactors are considered extremely safe.[167]

Runaway reactions cannot occur in a fusion reactor. The plasma is burnt at optimal conditions, and any significant change will quench the reactions. The reaction process is so delicate that this level of safety is inherent. Although the plasma in a fusion power plant is expected to have a volume of 1,000 cubic metres (35,000 cu ft) or more, the plasma density is low and the total amount of fusion fuel in the vessel typically only a few grams.[167] If the fuel supply is closed, the reaction stops within seconds. In comparison, a fission reactor is typically loaded with enough fuel for several years, and no additional fuel is necessary to continue the reaction.[168]

In the magnetic approach, strong fields are developed in coils that are held in place mechanically by the reactor structure. Failure of this structure could release this tension and allow the magnet to "explode" outward. The severity of this event would be similar to any other industrial accident or an MRI machine quench/explosion, and could be effectively stopped with a containment building similar to those used in existing (fission) nuclear generators. The laser-driven inertial approach is generally lower-stress. Although failure of the reaction chamber is possible, simply stopping fuel delivery would prevent any sort of catastrophic failure.

Most reactor designs rely on liquid lithium as both a coolant and a method for converting stray neutrons from the reaction into tritium, which is fed back into the reactor as fuel. Lithium is highly flammable, and in the case of a fire it is possible that the lithium stored on-site could be burned up and escape. In this case, the tritium contents of the lithium would be released into the atmosphere, posing a radiation risk. Calculations suggest that at about 1 kg the total amount of tritium and other radioactive gases in a typical power plant would be so small that they would have diluted to legally acceptable limits by the time they blew as far as the plant's perimeter fence.[169]

The likelihood of small industrial accidents including the local release of radioactivity and injury to staff cannot be estimated yet. These would include accidental releases of lithium, tritium, or mis-handling of decommissioned radioactive components of the reactor itself.

Magnet quench

A quench is an abnormal termination of magnet operation that occurs when part of the superconducting coil enters the normal (resistive) state. This can occur because the field inside the magnet is too large, the rate of change of field is too large (causing eddy currents and resultant heating in the copper support matrix), or a combination of the two.

More rarely a defect in the magnet can cause a quench. When this happens, that particular spot is subject to rapid Joule heating from the enormous current, which raises the temperature of the surrounding regions. This pushes those regions into the normal state as well, which leads to more heating in a chain reaction. The entire magnet rapidly becomes normal (this can take several seconds, depending on the size of the superconducting coil). This is accompanied by a loud bang as the energy in the magnetic field is converted to heat, and rapid boil-off of the cryogenic fluid. The abrupt decrease of current can result in kilovolt inductive voltage spikes and arcing. Permanent damage to the magnet is rare, but components can be damaged by localized heating, high voltages, or large mechanical forces.

In practice, magnets usually have safety devices to stop or limit the current when the beginning of a quench is detected. If a large magnet undergoes a quench, the inert vapor formed by the evaporating cryogenic fluid can present a significant asphyxiation hazard to operators by displacing breathable air.

A large section of the superconducting magnets in CERN's Large Hadron Collider unexpectedly quenched during start-up operations in 2008, necessitating the replacement of a number of magnets.[170] In order to mitigate against potentially destructive quenches, the superconducting magnets that form the LHC are equipped with fast-ramping heaters which are activated once a quench event is detected by the complex quench protection system. As the dipole bending magnets are connected in series, each power circuit includes 154 individual magnets, and should a quench event occur, the entire combined stored energy of these magnets must be dumped at once. This energy is transferred into dumps that are massive blocks of metal which heat up to several hundreds of degrees Celsius due to the resistive heating in a matter of seconds. Although undesirable, a magnet quench is a "fairly routine event" during the operation of a particle accelerator.[171]


The natural product of the fusion reaction is a small amount of helium, which is completely harmless to life. Of more concern is tritium, which, like other isotopes of hydrogen, is difficult to retain completely. During normal operation, some amount of tritium will be continually released. There would be no acute danger, but the cumulative effect on the world's population from a fusion economy could be a matter of concern.[citation needed]

Although tritium is volatile and biologically active, the health risk posed by a release is much lower than that of most radioactive contaminants, due to tritium's short half-life (12.32 years), very low decay energy (~14.95 keV), and the fact that it does not bioaccumulate (instead being cycled out of the body as water, with a biological half-life of 7 to 14 days).[172] Current ITER designs are investigating total containment facilities for any tritium.

Waste management

The large flux of high-energy neutrons in a reactor will make the structural materials radioactive. The radioactive inventory at shut-down may be comparable to that of a fission reactor, but there are important differences.

The half-life of the radioisotopes produced by fusion tends to be less than those from fission, so that the inventory decreases more rapidly. Unlike fission reactors, whose waste remains radioactive for thousands of years, most of the radioactive material in a fusion reactor would be the reactor core itself, which would be dangerous for about 50 years, and low-level waste another 100. Although this waste will be considerably more radioactive during those 50 years than fission waste, the very short half-life makes the process very attractive, as the waste management is fairly straightforward. By 500 years the material would have the same radiotoxicity as coal ash.[169]

Additionally, the choice of materials used in a fusion reactor is less constrained than in a fission design, where many materials are required for their specific neutron cross-sections. This allows a fusion reactor to be designed using materials that are selected specifically to be "low activation", materials that do not easily become radioactive. Vanadium, for example, would become much less radioactive than stainless steel. Carbon fiber materials are also low-activation, as well as being strong and light, and are a promising area of study for laser-inertial reactors where a magnetic field is not required.

In general terms, fusion reactors would create far less radioactive material than a fission reactor, the material it would create is less damaging biologically, and the radioactivity "burns off" within a time period that is well within existing engineering capabilities for safe long-term waste storage.

Nuclear proliferation

Although fusion power uses nuclear technology, the overlap with nuclear weapons would be limited. A huge amount of tritium could be produced by a fusion power plant; tritium is used in the trigger of hydrogen bombs and in a modern boosted fission weapon, but it can also be produced by nuclear fission. The energetic neutrons from a fusion reactor could be used to breed weapons-grade plutonium or uranium for an atomic bomb (for example by transmutation of U238 to Pu239, or Th232 to U233).

A study conducted 2011 assessed the risk of three scenarios:[173]

  • Use in small-scale fusion plant: Due to much higher power consumption, heat dissipation and a more unique design compared to enrichment gas centrifuges this choice would be much easier to detect and therefore implausible.[173]
  • Modifications to produce weapon-usable material in a commercial facility: The production potential is significant. But no fertile or fissile substances necessary for the production of weapon-usable materials needs to be present at a civil fusion system at all. If not shielded, a detection of these materials can be done by their characteristic gamma radiation. The underlying redesign could be detected by regular design information verifications. In the (technically more feasible) case of solid breeder blanket modules, it would be necessary for incoming components to be inspected for the presence of fertile material,[173] otherwise plutonium for several weapons could be produced each year.[174]
  • Prioritizing a fast production of weapon-grade material regardless of secrecy: The fastest way to produce weapon usable material was seen in modifying a prior civil fusion power plant. Unlike in some nuclear power plants, there is no weapon compatible material during civil use. Even without the need for covert action this modification would still take about 2 months to start the production and at least an additional week to generate a significant amount for weapon production. This was seen as enough time to detect a military use and to react with diplomatic or military means. To stop the production, a military destruction of inevitable parts of the facility leaving out the reactor itself would be sufficient. This, together with the intrinsic safety of fusion power would only bear a low risk of radioactive contamination.[173]

Another study concludes that "[..]large fusion reactors – even if not designed for fissile material breeding – could easily produce several hundred kg Pu per year with high weapon quality and very low source material requirements." It was emphasized that the implementation of features for intrinsic proliferation resistance might only be possible at this phase of research and development.[174] The theoretical and computational tools needed for hydrogen bomb design are closely related to those needed for inertial confinement fusion, but have very little in common with the more scientifically developed magnetic confinement fusion.

Energy source

Large-scale reactors using neutronic fuels (e.g. ITER) and thermal power production (turbine based) are most comparable to fission power from an engineering and economics viewpoint. Both fission and fusion power plants involve a relatively compact heat source powering a conventional steam turbine-based power plant, while producing enough neutron radiation to make activation of the plant materials problematic. The main distinction is that fusion power produces no high-level radioactive waste (though activated plant materials still need to be disposed of). There are some power plant ideas that may significantly lower the cost or size of such plants; however, research in these areas is nowhere near as advanced as in tokamaks.[citation needed]

Fusion power commonly proposes the use of deuterium, an isotope of hydrogen, as fuel and in many current designs also use lithium. Assuming a fusion energy output equal to the 1995 global power output of about 100 EJ/yr (= 1 × 1020 J/yr) and that this does not increase in the future, which is unlikely, then the known current lithium reserves would last 3000 years. Lithium from sea water would last 60 million years, however, and a more complicated fusion process using only deuterium from sea water would have fuel for 150 billion years.[175] To put this in context, 150 billion years is close to 30 times the remaining lifespan of the sun,[176] and more than 10 times the estimated age of the universe.


While fusion power is still in early stages of development, substantial sums have been and continue to be invested in research. In the EU almost €10 billion was spent on fusion research up to the end of the 1990s, and the new ITER reactor alone is budgeted at €6.6 billion total for the timeframe between 2008 and 2020[177].

It is estimated that up to the point of possible implementation of electricity generation by nuclear fusion, R&D will need further promotion totalling around €60–80 billion over a period of 50 years or so (of which €20–30 billion within the EU) based on a report from 2002.[178] Nuclear fusion research receives €750 million (excluding ITER funding) from the European Union, compared with €810 million for sustainable energy research,[179] putting research into fusion power well ahead of that of any single rivaling technology. Indeed, the size of the investments and time frame of the expected results mean that fusion research is almost exclusively publicly funded, while research in other forms of energy can be done by the private sector. In spite of that, a number of start-up companies active in the field of fusion power have managed to attract private money.[180]


Fusion power would provide more energy for a given weight of fuel than any fuel-consuming energy source currently in use,[181] and the fuel itself (primarily deuterium) exists abundantly in the Earth's ocean: about 1 in 6500 hydrogen atoms in seawater is deuterium.[182] Although this may seem a low proportion (about 0.015%), because nuclear fusion reactions are so much more energetic than chemical combustion and seawater is easier to access and more plentiful than fossil fuels, fusion could potentially supply the world's energy needs for millions of years.[183][184]

Despite being technically non-renewable, fusion power has many of the benefits of renewable energy sources (such as being a long-term energy supply and emitting no greenhouse gases) as well as some of the benefits of the resource-limited energy sources as hydrocarbons and nuclear fission (without reprocessing). Like these currently dominant energy sources, fusion could provide very high power-generation density and uninterrupted power delivery (due to the fact that it is not dependent on the weather, unlike wind and solar power).

Another aspect of fusion energy is that the cost of production does not suffer from diseconomies of scale. The cost of water and wind energy, for example, goes up as the optimal locations are developed first, while further generators must be sited in less ideal conditions. With fusion energy the production cost will not increase much even if large numbers of plants are built, because the raw resource (seawater) is abundant and widespread.

Some problems that are expected to be an issue in this century, such as fresh water shortages, can alternatively be regarded as problems of energy supply. For example, in desalination plants, seawater can be purified through distillation or reverse osmosis. Nonetheless, these processes are energy intensive. Even if the first fusion plants are not competitive with alternative sources, fusion could still become competitive if large-scale desalination requires more power than the alternatives are able to provide.

A scenario has been presented of the effect of the commercialization of fusion power on the future of human civilization.[185] ITER and later Demo are envisioned to bring online the first commercial nuclear fusion energy reactor by 2050. Using this as the starting point and the history of the uptake of nuclear fission reactors as a guide, the scenario depicts a rapid take up of nuclear fusion energy starting after the middle of this century.

Fusion power could be used in interstellar space, where solar energy is not available.[186]

See also


  1. "ICF Physics" 2004, Atzeni, Chapter 1, page 1
  2. "Nuclear Fusion : WNA". world-nuclear.org. November 2015.<templatestyles src="Module:Citation/CS1/styles.css"></templatestyles>
  3. "Fission and fusion can yield energy". Hyperphysics.phy-astr.gsu.edu. Retrieved 30 October 2014.<templatestyles src="Module:Citation/CS1/styles.css"></templatestyles>
  4. "Fission and Fusion". Newton.dep.anl.gov. 2000. Retrieved 2014-08-24.<templatestyles src="Module:Citation/CS1/styles.css"></templatestyles>
  5. 5.0 5.1 5.2 5.3 Miley, G.H.; Towner, H.; Ivich, N. (1974-06-17). "SciTech Connect: Fusion cross sections and reactivities". Osti.gov. doi:10.2172/4014032. Retrieved 2014-08-24.<templatestyles src="Module:Citation/CS1/styles.css"></templatestyles>
  6. 6.0 6.1 6.2 6.3 6.4 "Some Criteria for a Power producing thermonuclear reactor" John Lawson, Atomic Energy Research Establishment, Hanvell, Berks, 2nd November 1956
  7. "Lawson's three criteria". EFDA. February 25, 2013. Retrieved 2014-08-24.<templatestyles src="Module:Citation/CS1/styles.css"></templatestyles>
  8. "Triple product". EFDA. 2014-06-20. Retrieved 2014-08-24.<templatestyles src="Module:Citation/CS1/styles.css"></templatestyles>
  9. Richard Fitzpatrick, Introduction to Plasma Physics, Magnetized plasmas
  10. Alfvén, H (1942). "Existence of electromagnetic-hydrodynamic waves". Nature. 150: 405–406. Bibcode:1942Natur.150..405A. doi:10.1038/150405d0.<templatestyles src="Module:Citation/CS1/styles.css"></templatestyles>
  11. Tuszewski, M. (1988). "Field reversed configurations". Nuclear Fusion. 28 (11): 2033–2092. doi:10.1088/0029-5515/28/11/008.<templatestyles src="Module:Citation/CS1/styles.css"></templatestyles>
  12. Engelhardt, W. (2005-01-01). "Is a Plasma Diamagnetic?". Physics Essays. 18 (4). arXiv:physics/0510139. Bibcode:2005PhyEs..18..504E. doi:10.4006/1.3025762.<templatestyles src="Module:Citation/CS1/styles.css"></templatestyles>
  13. R. F. Post, Proc. of Second U.N. Int. Conf. on Peaceful Uses of Atomic Energy, Vol. 32, p. 245 (Geneva, 1958)
  14. "Laser Inertial Fusion Energy". Life.llnl.gov. Retrieved 2014-08-24.<templatestyles src="Module:Citation/CS1/styles.css"></templatestyles>
  15. 15.0 15.1 "Experimental results from a beam direct converter at 100 kV" R. W. MOIR, W. L. BARR, Journal of fusion energy, Volume 2, No 2, 1982
  16. "All-the-Worlds-Tokamaks". tokamak.info.<templatestyles src="Module:Citation/CS1/styles.css"></templatestyles>
  17. "MIT tests unique approach to fusion power". MIT News, David Chandler, MIT News Office, March 19, 2008. Accessed March 2008
  18. 18.0 18.1 "Mirror Systems: Fuel Cycles, loss reduction and energy recovery" by Richard F. Post, BNES Nuclear fusion reactor conferences at Culham laboratory, September 1969.
  19. J Berowitz, H Grad and H Rubin, in proceedings of the second United Nations International conference on peaceful uses of atomic energy, Geneva, 1958, Vol 31, Page 177
  20. Freidberg, Jeffrey P. (2007). Plasma Physics and Fusion Energy. Cambridge University Press. ISBN 0-521-85107-6.
  21. 21.0 21.1 Nuckolls, John; Wood, Lowell; Thiessen, Albert; Zimmerman, George (1972). "Laser Compression of Matter to Super-High Densities: Thermonuclear (CTR) Applications". Nature. 239: 139–142. Bibcode:1972Natur.239..139N. doi:10.1038/239139a0.<templatestyles src="Module:Citation/CS1/styles.css"></templatestyles>
  22. Y. C. Francis Thio Ph.D., Program Manager, U. S. Department of Energy, Office of Fusion Energy Sciences, Germantown, Maryland, United States. "Status of the U. S. program in magneto-inertial fusion" (PDF). Iopscience.iop.org. Retrieved 30 October 2014.CS1 maint: multiple names: authors list (link)<templatestyles src="Module:Citation/CS1/styles.css"></templatestyles>
  24. 24.0 24.1 Seife, Charles. Sun in a Bottle: The Strange History of Fusion and the Science of Wishful Thinking. 1st ed. Vol. 1. N.p.: Penguin, 2008. Print.
  25. 25.0 25.1 Phillips, James. "Magnetic Fusion." Los Alamos Science Winter 1983: 64-67. Web. 4 Apr. 2013.
  26. Srivastava, K. M.; Vyas, D. N., "Non-linear analysis of the stability of the screw pinch", (1982) Astrophysics and Space Science, vol. 86, no. 1, Aug. 1982, p. 71-89
  27. "A general critique of inertial-electrostatic confinement fusion systems" Plasma Physics, June 1995, Dr. Todd Rider, MIT
  28. "The Boy Who Played With Fusion". Popular Science. Retrieved October 18, 2013.
  29. US patent 5,160,695, Robert W. Bussard, "Method and apparatus for creating and controlling nuclear fusion reactions", issued 1992-11-03
  30. FRX-L: A Plasma Injector for Magnetized Target Fusion
  31. "Spherically imploding plasma liners as a standoff driver for MIF" IEEE transactions, 2012, Hsu, et al.
  32. Chang, Kenneth (February 27, 2007). "Practical Fusion, or Just a Bubble?". New York Times. Retrieved 2007-02-27. "Dr. Putterman's approach is to use sound waves, called sonofusion or bubble fusion, to expand and collapse tiny bubbles, generating ultrahot temperatures. At temperatures hot enough, atoms can literally fuse and release even more energy than when they split in nuclear fission, now used in nuclear power plants and weapons. Furthermore, fusion is clean in that it does not produce long-lived nuclear waste."
  33. Chang, Kenneth (2004-03-25), US will give cold fusion a second look, The New York Times, retrieved 2009-02-08.
  34. Ouellette, Jennifer (2011-12-23), Could Starships Use Cold Fusion Propulsion?, Discovery News.
  35. Huizenga, John R. (1993), Cold Fusion: The Scientific Fiasco of the Century (2nd ed.), Oxford and New York: Oxford University Press, p. 112, ISBN 0-19-855817-1<templatestyles src="Module:Citation/CS1/styles.css"></templatestyles>
  36. "NEUTRAL-BEAM INJECTION" W. B. Kunkel, Lawrence Livermore National Labs, FUSION, 1980
  37. McGuire, Thomas. Heating Plasma for Fusion Power Using Magnetic Field Oscillations. Baker Botts LLP, assignee. Issued: 4/2/14, Patent 14/243,447. N.d. Print.
  38. "Nonlinear Thomson scattering of intense laser pulses from beams and plasma" Phys. Rev. E 48, 3003 – Published 1 October 1993 Eric Esarey, Sally K. Ride, and Phillip Sprangle
  39. "Thomson scattering system on the TEXTOR tokamak using a multi-pass laser beam configuration" M Yu Kantor, A J H Donné, R Jaspers, Plasma Physics and Controlled Fusion, Volume 51, 5
  40. Mott-Smith, H. M. and Langmuir, Irving (1926). "The Theory of Collectors in Gaseous Discharges". Phys. Rev. 28 (4): 727–763.
  41. "NCSX Vacuum Vessel External Flux Loops Design and Installation, PPPL, Twenty-Second Symposium on Fusion Engineering, 2007
  42. Park, Jaeyoung; Krall, Nicholas A.; Sieck, Paul E.; Offermann, Dustin T.; Skillicorn, Michael; Sanchez, Andrew; Davis, Kevin; Alderson, Eric; Lapenta, Giovanni (2014-06-01). "High Energy Electron Confinement in a Magnetic Cusp Configuration". arXiv:1406.0133 [physics].<templatestyles src="Module:Citation/CS1/styles.css"></templatestyles>
  43. J. Larmor, "On a dynamical theory of the electric and luminiferous medium", Philosophical Transactions of the Royal Society 190, (1897) pp. 205–300 (Third and last in a series of papers with the same name).
  44. "Study of steam, helium and supercritical CO2 turbine power generations in prototype fusion power reactor", S Ishiyama, Y Muto, Y Kato, S Nishio, Progress in Nuclear Fusion, 2008
  45. "Laser sets records for neutron yield, laser energy". Phys.org. November 8, 2010. Retrieved 2014-08-24.<templatestyles src="Module:Citation/CS1/styles.css"></templatestyles>
  46. T. Anklam; A. J. Simon; S. Powers; W. R. Meier (December 2, 2010). "LIFE: The Case for Early Commercialization of Fusion Energy" (PDF). Livermore, LLNL-JRNL-463536. Retrieved 30 October 2014.<templatestyles src="Module:Citation/CS1/styles.css"></templatestyles>
  47. "Mirror Systems: Fuel Cycles, loss reduction and energy recovery" by Richard F. Post, BNES Nuclear fusion reactor conferences at Culham laboratory, September 1969
  48. "Test results on plasma direct converters" William L. Barr and Ralph W Moir, Nuclear Technology Vol 3, January 1983
  49. Wesson, J: "Tokamaks", 3rd edition page 115, Oxford University Press, 2004
  50. "Improved Confinement During Magnetic Levitation in LDX", 50th Annual Meeting of the APS DDP, November 18, 2008 M Manuel
  51. Ono, Y (1999). "New relaxation of merging spheromaks to a field reversed configuration". Nuclear Fusion 39 (11Y): 2001–2008. doi:10.1088/0029-5515/39/11Y/346. edit
  52. "Advanced Spheromak Fusion Reactor" T Fowler, E Hooper, 8th international conference on emerging nuclear energy ystems
  53. Booth, William. "Fusion's $372-Million Mothball." Science [New York City] 9 Oct. 1987, Volume 238 ed.: 152-55. Print
  54. Containment in a cusped Plasma System, Dr. Harold Grad, NYO-9496
  55. Pfalzner, Susanne (2006). An Introduction to Inertial Confinement Fusion. USA: Taylor & Francis. pp. 19–20. ISBN 0-7503-0701-3.<templatestyles src="Module:Citation/CS1/styles.css"></templatestyles>
  56. Pfalzner, Susanne (2006). An Introduction to Inertial Confinement Fusion. USA: Taylor & Francis. pp. 182–193. ISBN 0-7503-0701-3.<templatestyles src="Module:Citation/CS1/styles.css"></templatestyles>
  57. Ion Flow and Fusion Reactivity, Characterization of a Spherically convergent ion Focus. PhD Thesis, Dr. Timothy A Thorson, Wisconsin-Madison 1996.
  58. "Stable, thermal equilibrium, large-amplitude, spherical plasma oscillations in electrostatic confinement devices", DC Barnes and Rick Nebel, PHYSICS OF PLASMAS VOLUME 5, NUMBER 7 JULY 1998
  59. Carr, M.; Khachan, J. (2013). "A biased probe analysis of potential well formation in an electron only, low beta Polywell magnetic field". Physics of Plasmas 20 (5): 052504. Bibcode:2013PhPl...20e2504C. doi:10.1063/1.4804279
  60. "British Patent 817681". V3.espacenet.com. Retrieved 2013-06-22.<templatestyles src="Module:Citation/CS1/styles.css"></templatestyles>
  61. Nathaniel Fisch. Edward Teller Centennial Symposium. Books.google.com. p. 118. Retrieved 30 October 2014.<templatestyles src="Module:Citation/CS1/styles.css"></templatestyles>
  62. Lyman J Spitzer, "The Physics of Fully Ionized Gases" 1963
  63. [1] Archived October 30, 2014 at the Wayback Machine
  64. "Nuclear Power: A Very Short Introduction" 2011, page 90, Maxwell Irvine
  65. Cartlidge, Edwin. The Secret World of Amateur Fusion. Physics World, March 2007: IOP Publishing Ltd, pp. 10-11. ISSN 0953-8585.
  66. US Patent 3,258,402 June 28, 1966
  67. US Patent 3,386,883 June 4, 1968
  68. Robert L. Hirsch, "Inertial-Electrostatic Confinement of Ionized Fusion Gases", Journal of Applied Physics, v. 38, no. 7, October 1967
  69. M.H. Key 1985 Nucl. Fusion 25 1351, doi:10.1088/0029-5515/25/9/063
  70. "A Piece of the sun" by Dan Clery, June 2014
  71. Long 1976, p. 25.
  72. Principals of plasma physics, Nicholas Krall, 1973, Page 273
  73. "Summary of results from the tandem mirror experiment, TMX group, February 26, 1981
  74. "TMX Major Project proposal" Fred Coensgen, January 12, 1977
  75. Booth, William. "Fusion's $372-Million Mothball." Science [New York City] 9 Oct. 1987, Volume 238 ed.: 152-55. Print.
  76. Koppel, Niko (May 20, 2010). "Edwin E. Kintner, Nuclear Power Pioneer, Dies at 90". NYTimes.com. Retrieved 2014-08-24.<templatestyles src="Module:Citation/CS1/styles.css"></templatestyles>
  77. "Dr. Donna Strickland | Science". Uwaterloo.ca. Retrieved 2014-08-24.<templatestyles src="Module:Citation/CS1/styles.css"></templatestyles>
  78. 78.0 78.1 Dr. Matthew McKinzie; Christopher E. Paine (2000). "When peer review fails : The Roots of the National Ignition Facility (NIF) Debacle". National Resources Defense Council. Retrieved 30 October 2014.<templatestyles src="Module:Citation/CS1/styles.css"></templatestyles>
  79. "Recent Progress on the Los Alamos Aurora ICF (Inertial Confinement Fusion) Laser System." L. A. Rosocha, L. S. Blair, Publication Date, 1987.
  80. "Los Alamos National Labs Aurora Laser Fusion Project | Hextek Corp". Hextek.com. 2014-06-20. Retrieved 2014-08-24.<templatestyles src="Module:Citation/CS1/styles.css"></templatestyles>
  81. Hasegawa, A., Comments on Plasma Physics and Controlled Fusion, 1987, vol. 1, p. 147.
  82. [2] Archived November 15, 2012 at the Wayback Machine
  83. University of Utah, "'Simple experiment' results in sustained n-fusion at room temperature for first time", Newenergytimes.com, retrieved 28 July 2011 Cite journal requires |journal= (help)CS1 maint: ref=harv (link)<templatestyles src="Module:Citation/CS1/styles.css"></templatestyles>
  84. Browne 1989, Close 1992, Huizenga 1993, Taubes 1993
  85. 85.0 85.1 Browne 1989
  86. Chang, Kenneth (2004-03-25). "US will give cold fusion a second look". The New York Times. Retrieved 2009-02-08.<templatestyles src="Module:Citation/CS1/styles.css"></templatestyles>
  87. Voss 1999, Platt 1998, Goodstein 1994, Van Noorden 2007, Beaudette 2002, Feder 2005, Hutchinson 2006, Kruglinksi 2006, Adam 2005
  88. William J. Broad (31 October 1989). "Despite Scorn, Team in Utah Still Seeks Cold-Fusion Clues". The New York Times. pp. C1.<templatestyles src="Module:Citation/CS1/styles.css"></templatestyles>
  89. Alfred 2009
  90. "'Cold fusion' rebirth? New evidence for existence of controversial energy source" (Press release). American Chemical Society. Retrieved 30 October 2014.<templatestyles src="Module:Citation/CS1/styles.css"></templatestyles>
  91. Hagelstein et al. 2004
  92. Feder 2005
  93. Choi 2005, Feder 2005, US DOE 2004
  94. Y-K Martin Peng, "Spherical Torus, Compact Fusion at Low Yield"., ORNL/FEDC-87/7 (December 1984)
  95. Sykes 1997, pg. B247
  96. 96.0 96.1 Braams and Scott, pg. 225
  97. Sykes 2008, pg. 11
  98. "Neutron measurements from the preliminary tritium experiment at JET (invited)". 2006-06-16. Retrieved 2014-08-24.<templatestyles src="Module:Citation/CS1/styles.css"></templatestyles>
  99. Lindl, John; McCrory, Robert L.; Campbell, E. Michael (1992), "Progress Toward Ignition and Burn Propagation in Inertial Confinement Fusion" (PDF), Physics Today, 45: 32–40, Bibcode:1992PhT....45i..32L, doi:10.1063/1.881318<templatestyles src="Module:Citation/CS1/styles.css"></templatestyles>
  100. Lindl, John (1995-11-01). "Development of the indirect‐drive approach to inertial confinement fusion and the target physics basis for ignition and gain". Physics of Plasmas (1994-present). 2 (11): 3933–4024. Bibcode:1995PhPl....2.3933L. doi:10.1063/1.871025. ISSN 1070-664X.<templatestyles src="Module:Citation/CS1/styles.css"></templatestyles>
  101. Krall, N. A.; Coleman, M.; Maffei, K.; Lovberg, J.; Jacobsen, R.; Bussard, R. W. (1995). "Forming and maintaining a potential well in a quasispherical magnetic trap". Physics of Plasmas 2: 146.
  102. "Inertial electrostatic fusion (IEF): A clean energy future" (Microsoft Word document). Energy/Matter Conversion Corporation. Retrieved 2006-12-03.
  103. "Fundamental limitations on plasma fusions systems not in thermodynamic equilibrium" Thesis, Todd Rider, June 1995
  104. Nevins, William M. "Can Inertial Electrostatic Confinement Work beyond the Ion-ion Collisional Time Scale?" Physics of Plasmas 2.10 (1995): 3804-819. Print.
  105. ""IEC Lab Timeline" accessed 1-25-2014". Iec.neep.wisc.edu. Retrieved 30 October 2014.<templatestyles src="Module:Citation/CS1/styles.css"></templatestyles>
  106. "A portable neutron/tunable X-ray source based on inertial electrostatic confinement", Nuclear Instruments and Methods in Physics Research, A 422 (1999) 16-20
  107. [3][dead link]
  108. "NSD-GRADEL-FUSION - Neutron Generators". Nsd-fusion.com. Retrieved 2014-08-24.<templatestyles src="Module:Citation/CS1/styles.css"></templatestyles>
  109. "The IEC star-mode fusion neutron source for NAA--status and next-step designs". Appl Radiat Isot 53 (4-5): 779–83. October 2000.
  110. [4][dead link]
  111. [5] Archived October 4, 2012 at the Wayback Machine
  112. "Output of Sandia Z Accelerator Climbs Closer to Fusion". Sandia.gov. August 1, 1997. Retrieved 2014-08-24.<templatestyles src="Module:Citation/CS1/styles.css"></templatestyles>
  113. "Another dramatic climb toward fusion conditions for Sandia Z accelerator". Sandia.gov. Retrieved 2014-08-24.<templatestyles src="Module:Citation/CS1/styles.css"></templatestyles>
  114. "High-Output Sandia Accelerator Able to Predict Nuclear Blast Physics". Sandia.gov. December 2, 1996. Retrieved 2014-08-24.<templatestyles src="Module:Citation/CS1/styles.css"></templatestyles>
  115. [6] Archived May 27, 2010 at the Wayback Machine
  116. "Fusor Forums • Index page". Fusor.net. Retrieved 2014-08-24.<templatestyles src="Module:Citation/CS1/styles.css"></templatestyles>
  117. "Build a Nuclear Fusion Reactor? No Problem". Clhsonline.net. 2012-03-23. Retrieved 2014-08-24.<templatestyles src="Module:Citation/CS1/styles.css"></templatestyles>
  118. "Extreme DIY: Building a homemade nuclear reactor in NYC". BBC News. Retrieved 30 October 2014.<templatestyles src="Module:Citation/CS1/styles.css"></templatestyles>
  119. Schechner, Sam (2008-08-18). "Nuclear Ambitions: Amateur Scientists Get a Reaction From Fusion - WSJ". Online.wsj.com. Retrieved 2014-08-24.<templatestyles src="Module:Citation/CS1/styles.css"></templatestyles>
  120. "Will's Amateur Science and Engineering: Fusion Reactor's First Light!". Tidbit77.blogspot.com. 2010-02-09. Retrieved 2014-08-24.<templatestyles src="Module:Citation/CS1/styles.css"></templatestyles>
  121. Taleyarkhan, R. P.; C. D. West; J. S. Cho; R. T. Lahey; Jr. R. Nigmatulin; R. C. Block (2002-03-08). "Evidence for Nuclear Emissions During Acoustic Cavitation". Science. 295 (1868): 1868–73. Bibcode:2002Sci...295.1868T. doi:10.1126/science.1067589. PMID 11884748. Retrieved 2007-05-13.<templatestyles src="Module:Citation/CS1/styles.css"></templatestyles>
  122. Purdue physicist found guilty of misconduct, Los Angeles Times, July 19, 2008, Thomas H. Maugh II
  123. 123.0 123.1 Reich, Eugenie Samuel (23 November 2009). "Bubble-fusion scientist debarred from federal funding". Nature. doi:10.1038/news.2009.1103.<templatestyles src="Module:Citation/CS1/styles.css"></templatestyles>
  124. Science News Staff (23 November 2009), "Roundup 11/23: Keep Your Eyes on the Prize Edition", Science Insider<templatestyles src="Module:Citation/CS1/styles.css"></templatestyles>. It cites "New Energy Times Special Edition #33", New Energy Times (33), November 20, 2009<templatestyles src="Module:Citation/CS1/styles.css"></templatestyles>
  125. "The Year in Science: Physics". Web.archive.org. 2006-10-21. Archived from the original on February 17, 2012. Retrieved 2013-06-22. Unknown parameter |deadurl= ignored (help)<templatestyles src="Module:Citation/CS1/styles.css"></templatestyles>
  126. "Equilibrium and low-frequency stability of a uniform density, collisionless, spherical Vlasov system" DC Barns, L Chacon, Physics of plasma November 2002
  127. "Observation of Spherical Focus in an Electron Penning Trap", T. B. Mitchell and M. M. Schauer, PHYSICAL REVIEW LETTERS, VOLUME 78, NUMBER 1
  128. Ph.D. Thesis "Improving Particle Confinement in Inertial Electrostatic Fusion for Spacecraft Power and Propulsion", Carl Dietrich, MASSACHUSETTS INSTITUTE OF TECHNOLOGY FEBRUARY 2007
  129. Ph.D. Thesis "Improved lifetimes and synchronization behavior in Mutlt-grid IEC fusion devices", Tom McGuire, MASSACHUSETTS INSTITUTE OF TECHNOLOGY FEBRUARY 2007
  130. "Phoenix Nuclear Labs meets neutron production milestone", PNL press release May 1, 2013, Ross Radel, Evan Sengbusch
  131. SirPhilip (posting an e-mail from "RW Bussard") (2006-06-23). "Fusion, eh?". James Randi Educational Foundation forums. Retrieved 2006-12-03.
  132. "The Advent of Clean Nuclear Fusion: Super-performance Space Power and Propulsion", Robert W. Bussard, Ph.D., 57th International Astronautical Congress, October 2–6, 2006
  133. Dutton, Judy. "Teen Nuclear Scientist Fights Terror", CNN.com, September 1, 2011. Retrieved September 3, 2011.
  134. "Rock Center: 19-year-old hopes to revolutionize nuclear power". NBC. Retrieved October 18, 2013.
  135. TED2013. "Taylor Wilson: My radical plan for small nuclear fission reactors". TED.com. Retrieved May 6, 2013.
  136. May, Kate Torgovnick (February 27, 2013). "Good energy comes in small packages: Taylor Wilson at TED2013". TED blog — Science. TED (conference). Retrieved 2014-02-10.<templatestyles src="Module:Citation/CS1/styles.css"></templatestyles>
  137. "President Obama Hosts the White House Science Fair". The White House. Retrieved October 18, 2013.
  138. ""US lab debuts super laser", Breitbart news site". Web.archive.org. 2010-12-24. Archived from the original on 2010-12-24. Retrieved 2013-06-22.<templatestyles src="Module:Citation/CS1/styles.css"></templatestyles>
  139. Seaver, Lynda L (2010-10-01). "World's largest laser sets records for neutron yield and laser energy". Llnl.gov. Retrieved 2013-06-22.<templatestyles src="Module:Citation/CS1/styles.css"></templatestyles>
  140. SPIE Europe Ltd. "PW 2012: fusion laser on track for 2012 burn". Optics.org. Retrieved 2013-06-22.<templatestyles src="Module:Citation/CS1/styles.css"></templatestyles>
  141. "First successful integrated experiment at National Ignition Facility announced". General Physics. PhysOrg.com. October 8, 2010. Retrieved 2010-10-09.<templatestyles src="Module:Citation/CS1/styles.css"></templatestyles>
  142. "Nuclear fusion milestone passed at US lab". BBC News. Retrieved 30 October 2014.<templatestyles src="Module:Citation/CS1/styles.css"></templatestyles>
  143. "Fusion, anyone? Not quite yet, but researchers show just how close we've come". Phys.org. September 24, 2013. Retrieved 2014-08-24.<templatestyles src="Module:Citation/CS1/styles.css"></templatestyles>
  144. Bishop, Breanna (August 27, 2013). "Laser fusion experiment yields record energy". Phys.org. Retrieved 2014-08-24.<templatestyles src="Module:Citation/CS1/styles.css"></templatestyles>
  145. "ADVANCES TOWARDS PB11 FUSION WITH THE DENSE PLASMA FOCUS", Eric Lerner, Lawrenceville Plasma Physics, 2008
  146. Kramer, David (2006-06-16). "Livermore ends LIFE". Scitation.aip.org. Retrieved 2014-08-24.<templatestyles src="Module:Citation/CS1/styles.css"></templatestyles>
  147. http://phoenixnuclearlabs.com/product/high-yield-neutron-generator/, press release
  148. "FuseNet: The European Fusion Education Network". Fusenet.eu. Retrieved 30 October 2014.<templatestyles src="Module:Citation/CS1/styles.css"></templatestyles>
  149. "Fusion Power Could Happen Sooner Than You Think". Popular Science. Retrieved 30 October 2014.<templatestyles src="Module:Citation/CS1/styles.css"></templatestyles>
  150. "Nuclear fusion energy in a decade? Lockheed Martin is betting on it". Washington Post. Retrieved 30 October 2014.<templatestyles src="Module:Citation/CS1/styles.css"></templatestyles>
  151. Norris, Guy (2014-10-14). "High Hopes – Can Compact Fusion Unlock New Power For Space And Air Transport?". Aviation Week. Retrieved 2014-10-30.<templatestyles src="Module:Citation/CS1/styles.css"></templatestyles>
  152. research.microsoft.com/apps/video/default.aspx?id=238715&r=1
  153. David L. Chandler - MIT News Office (10 August 2015). "A small, modular, efficient fusion plant". MIT News.<templatestyles src="Module:Citation/CS1/styles.css"></templatestyles>
  154. Atzeni, Stefano (2009). The Physics of Inertial Fusion. USA: Oxford Science Publications. pp. 12–13. ISBN 978-0-19-956801-7.<templatestyles src="Module:Citation/CS1/styles.css"></templatestyles>
  155. "Thinkquest: D-T reaction". Retrieved 12 June 2010.<templatestyles src="Module:Citation/CS1/styles.css"></templatestyles>
  156. Iiyoshi, A; H. Momota; O Motojima; et al. (October 1993). "Innovative Energy Production in Fusion Reactors". National Institute for Fusion Science NIFS: 2–3. Retrieved 14 February 2012.<templatestyles src="Module:Citation/CS1/styles.css"></templatestyles>
  157. "Nuclear Fusion Power, Assessing fusion power". World-nuclear.org. Retrieved 30 October 2014.<templatestyles src="Module:Citation/CS1/styles.css"></templatestyles>
  158. Rolfe, A. C. (1999). "Remote Handling JET Experience" (PDF). Nuclear Energy. 38 (5): 6. ISSN 0140-4067. Retrieved 10 April 2012.<templatestyles src="Module:Citation/CS1/styles.css"></templatestyles>
  159. M. Sawan, S. Zinkle, and J. Sheffield, Fusion Eng Des 61-2, 561 (2002).
  160. J. Kesner, D. Garnier, A. Hansen, M. Mauel, and L. Bromberg, Nucl Fusion 2004; 44, 193
  161. Heindler and Kernbichler, Proc. 5th Intl. Conf. on Emerging Nuclear Energy Systems, 1989, pp. 177–82. See also Residual radiation from a p–11B reactor
  162. "Nuclear Fusion: Laser-Beam Experiment Yields Exciting Results". LiveScience.com.<templatestyles src="Module:Citation/CS1/styles.css"></templatestyles>
  163. 163.0 163.1 "Thermal response of nanostructured tungsten"Shin Kajita, et al., January 2014, Nucl. Fusion 54 (2014) 033005 (10pp)
  164. Evans, Ll. M.; Margetts, L.; Casalegno, V.; Lever, L. M.; Bushell, J.; Lowe, T.; Wallwork, A.; Young, P.; Lindemann, A. (2015-05-28). "Transient thermal finite element analysis of CFC–Cu ITER monoblock using X-ray tomography data". Fusion Engineering and Design. 100: 100–111. doi:10.1016/j.fusengdes.2015.04.048.<templatestyles src="Module:Citation/CS1/styles.css"></templatestyles>
  165. Evans, Ll. M.; Margetts, L.; Casalegno, V.; Leonard, F.; Lowe, T.; Lee, P. D.; Schmidt, M.; Mummery, P. M. (2014-06-01). "Thermal characterisation of ceramic/metal joining techniques for fusion applications using X-ray tomography". Fusion Engineering and Design. 89 (6): 826–836. doi:10.1016/j.fusengdes.2014.05.002.<templatestyles src="Module:Citation/CS1/styles.css"></templatestyles>
  166. Dulon, Krista (2012). "Who is afraid of ITER?". iter.org. Retrieved 18 August 2012.<templatestyles src="Module:Citation/CS1/styles.css"></templatestyles>
  167. 167.0 167.1 McCracken, Garry; Stott, Peter (8 June 2012). Fusion: The Energy of the Universe. Academic Press. pp. 198–199. ISBN 978-0-12-384656-3. Retrieved 18 August 2012.<templatestyles src="Module:Citation/CS1/styles.css"></templatestyles>
  168. Angelo, Joseph A. (30 November 2004). Nuclear Technology. Greenwood Publishing Group. p. 474. ISBN 978-1-57356-336-9. Retrieved 18 August 2012.<templatestyles src="Module:Citation/CS1/styles.css"></templatestyles>
  169. 169.0 169.1 T. Hamacher and A.M. Bradshaw (October 2001). "Fusion as a Future Power Source: Recent Achievements and Prospects" (PDF). World Energy Council. Archived from the original (PDF) on 2004-05-06.<templatestyles src="Module:Citation/CS1/styles.css"></templatestyles>
  170. "Interim Summary Report on the Analysis of the 19 September 2008 Incident at the LHC" (PDF). CERN.<templatestyles src="Module:Citation/CS1/styles.css"></templatestyles>
  171. Peterson, Tom. "Explain it in 60 seconds: Magnet Quench". Symmetry Magazine. Fermilab/SLAC. Retrieved 15 February 2013.<templatestyles src="Module:Citation/CS1/styles.css"></templatestyles>
  172. Petrangeli, Gianni (2006). Nuclear Safety. Butterworth-Heinemann. p. 430. ISBN 978-0-7506-6723-4.<templatestyles src="Module:Citation/CS1/styles.css"></templatestyles>
  173. 173.0 173.1 173.2 173.3 R. J. Goldston, A. Glaser, A. F. Ross: "Proliferation Risks of Fusion Energy: Clandestine Production, Covert Production, and Breakout";9th IAEA Technical Meeting on Fusion Power Plant Safety (accessible at no cost, 2013) and Glaser, A.; Goldston, R. J. (2012). "Proliferation risks of magnetic fusion energy: Clandestine production, covert production and breakout". Nuclear Fusion. 52 (4): 043004. Bibcode:2012NucFu..52d3004G. doi:10.1088/0029-5515/52/4/043004.<templatestyles src="Module:Citation/CS1/styles.css"></templatestyles>
  174. 174.0 174.1 "Strong Neutron Sources - How to cope with weapon material production capabilities of fusion and spallation neutron sources?" Matthias Englert, Giorgio Franceschini, Wolfgang Liebert (2011); 7th INMM/Esarda Workshop, Aix‐en‐Provence
  175. "Energy for Future Centuries" (PDF). Retrieved 2013-06-22.<templatestyles src="Module:Citation/CS1/styles.css"></templatestyles>
  176. Dr. Eric Christian; et al. "Cosmicopia". NASA. Retrieved 2009-03-20.<templatestyles src="Module:Citation/CS1/styles.css"></templatestyles>
  177. Fusion For Energy. "Fusion For Energy - Bringing the power of the sun to earth". europa.eu.<templatestyles src="Module:Citation/CS1/styles.css"></templatestyles>
  178. "The current EU research programme" (PDF). FP6. Tab.fzk.de. Retrieved 30 October 2014.<templatestyles src="Module:Citation/CS1/styles.css"></templatestyles>
  179. "The Sixth Framework Programme in brief" (PDF). Ec.europa.eu. Retrieved 30 October 2014.<templatestyles src="Module:Citation/CS1/styles.css"></templatestyles>
  180. Lev Grossman 'Star power' , Time November 2, 2015 ,http://time.com/magazine/us/4082927/november-2nd-2015-vol-186-no-18-u-s/
  181. Robert F. Heeter; et al. "Conventional Fusion FAQ Section 2/11 (Energy) Part 2/5 (Environmental)". Fused.web.llnl.gov. Retrieved 30 October 2014.<templatestyles src="Module:Citation/CS1/styles.css"></templatestyles>
  182. Dr. Frank J. Stadermann. "Relative Abundances of Stable Isotopes". Laboratory for Space Sciences, Washington University in St. Louis. Archived from the original on 2011-07-20.<templatestyles src="Module:Citation/CS1/styles.css"></templatestyles>
  183. J. Ongena and G. Van Oost. "Energy for Future Centuries" (PDF). Laboratorium voor Plasmafysica– Laboratoire de Physique des Plasmas Koninklijke Militaire School– Ecole Royale Militaire; Laboratorium voor Natuurkunde, Universiteit Gent. pp. Section III.B. and Table VI.<templatestyles src="Module:Citation/CS1/styles.css"></templatestyles>
  184. EPS Executive Committee. "The importance of European fusion energy research". The European Physical Society. Archived from the original on 2008-10-08.<templatestyles src="Module:Citation/CS1/styles.css"></templatestyles>
  185. Sing Lee and Sor Heoh Saw. "Nuclear Fusion Energy-Mankind's Giant Step Forward" (PDF). HPlasmafocus.net. Retrieved 30 October 2014.<templatestyles src="Module:Citation/CS1/styles.css"></templatestyles>
  186. "What Is The Future Of Space Travel?". Zidbits. Retrieved 14 November 2015.<templatestyles src="Module:Citation/CS1/styles.css"></templatestyles>


External links