Glossary of experimental design

The following is a glossary of terms. It is not intended to be all-inclusive.

Concerned fields

• Statistics
• Experimental design
• Estimation theory

Glossary

• Alias: When the estimate of an effect also includes the influence of one or more other effects (usually high order interactions) the effects are said to be aliased (see confounding). For example, if the estimate of effect D in a four factor experiment actually estimates (D + ABC), then the main effect D is aliased with the 3-way interaction ABC. Note: This causes no difficulty when the higher order interaction is either non-existent or insignificant.
• Analysis of variance (ANOVA): A mathematical process for separating the variability of a group of observations into assignable causes and setting up various significance tests.
• Balanced design: An experimental design where all cells (i.e. treatment combinations) have the same number of observations.
• Blocking: A schedule for conducting treatment combinations in an experimental study such that any effects on the experimental results due to a known change in raw materials, operators, machines, etc., become concentrated in the levels of the blocking variable. Note: the reason for blocking is to isolate a systematic effect and prevent it from obscuring the main effects. Blocking is achieved by restricting randomization.
• Center Points: Points at the center value of all factor ranges.
• Coding Factor Levels: Transforming the scale of measurement for a factor so that the high value becomes +1 and the low value becomes -1 (see scaling). After coding all factors in a 2-level full factorial experiment, the design matrix has all orthogonal columns. Coding is a simple linear transformation of the original measurement scale. If the "high" value is X_h and the "low" value is X_L (in the original scale), then the scaling transformation takes any original X value and converts it to (X − a)/b, where a = (X_h + X_L)/2 and b = (X_h−X_L)/2. To go back to the original measurement scale, just take the coded value and multiply it by b and add a or, X = b × (coded value) + a. As an example, if the factor is temperature and the high setting is 65°C and the low setting is 55°C, then a = (65 + 55)/2 = 60 and b = (65 − 55)/2 = 5. The center point (where the coded value is 0) has a temperature of 5(0) + 60 = 60°C.
• Comparative design: A design that allows the (typically mean-unbiased) estimation of the difference in factor effects, especially for the difference in treatment effects. The estimation of differences between treatment effects can be made with greater reliability than the estimation of absolute treatment effects.
• Confounding: A confounding design is one where some treatment effects (main or interactions) are estimated by the same linear combination of the experimental observations as some blocking effects. In this case, the treatment effect and the blocking effect are said to be confounded. Confounding is also used as a general term to indicate that the value of a main effect estimate comes from both the main effect itself and also contamination or bias from higher order interactions. Note: Confounding designs naturally arise when full factorial designs have to be run in blocks and the block size is smaller than the number of different treatment combinations. They also occur whenever a fractional factorial design is chosen instead of a full factorial design.
• Control group: a set of experimental units to which incidental treatments are applied but not main treatments. For example, in applying a herbicide as one treatment, plots receiving that treatment might be driven over by a machine applying the herbicide but treatments not receiving the herbicide would not normally be driven over. The machine traffic is an incidental treatment. If there was a concern that the machine traffic might have an effect on the variable being measured (e.g. death of strawberry plants), then a control treatment would receive the machine traffic but no herbicide. Control groups are a way of eliminating the possibility of incidental treatments being the cause of measured effects. The incidental treatments are controlled for. Compare treatment groups. A treatment that is only the absence of the manipulation being studied is simply one of the treatments and not a control, though it is now common to refer to a non-manipulated treatment as a control.
• Crossed factors: See factors below.
• Design: A set of experimental runs which allows you to fit a particular model and estimate your desired effects.
• Design matrix: A matrix description of an experiment that is useful for constructing and analyzing experiments.
• Effect (of a factor): How changing the settings of a factor changes the response. The effect of a single factor is also called a main effect. A treatment effect may be assumed to be the same for each experimental unit, by the assumption of treatment-unit additivity; more generally, the treatment effect may be the average effect. Other effects may be block effects. (For a factor A with two levels, scaled so that low = -1 and high = +1, the effect of A has a mean-unbiased estimator that is evaluated by subtracting the average observed response when A is -1 from the average observed response when A = +1 and dividing the result by 2; division by 2 is needed because the -1 level is 2 scaled units away from the +1 level.)
• Error: Unexplained variation in a collection of observations. See Errors and residuals in statistics. Note: experimental designs typically require understanding of both random error and lack of fit error.
• Experimental unit: The entity to which a specific treatment combination is applied. For example, an experimental unit can be a
  • PC board
  • silicon wafer
  • tray of components simultaneously treated
  • individual agricultural plants
  • plot of land
  • automotive transmissions
  • etc.
• Factors: Process inputs that an investigator manipulates to cause a corresponding change in the output. Some factors cannot be controlled by the experimenter but may affect the responses. These uncontrolled factors should be measured and used in the data analysis, if their effect is significant. Note: The inputs can be discrete or continuous.
  • Crossed factors: Two factors are crossed if every level of one occurs with every level of the other in the experiment.
  • Nested factors: A factor "A" is nested within another factor "B" if the levels or values of "A" are different for every level or value of "B". Note: Nested factors or effects have a hierarchical relationship.
• Fixed effect: An effect associated with an input variable that has a limited number of levels or in which only a limited number of levels are of interest to the experimenter.
• Interaction: Occurs when the effect of one factor on a response depends on the level of another factor(s).
• Lack of fit error: Error that occurs when the analysis omits one or more important terms or factors from the process model. Note: Including replication in a designed experiment allows separation of experimental error into its components: lack of fit and random (pure) error.
• Model: Mathematical relationship which relates changes in a given response to changes in one or more factors.
• Nested Factors: See factors above.
• Orthogonality: Two vectors of the same length are orthogonal if the sum of the products of their corresponding elements is 0. Note: An experimental design is orthogonal if the effects of any factor balance out (sum to zero) across the effects of the other factors.
• Random effect: An effect associated with input variables chosen at random from a population having a large or infinite number of possible values.
• Random error: Error that occurs due to natural variation in the process. Note: Random error is typically assumed to be normally distributed with zero mean and a constant variance. Note: Random error is also called experimental error.
• Randomization: A schedule for allocating treatment material and for conducting treatment combinations in a designed experiment such that the conditions in one run neither depend on the conditions of the previous run nor predict the conditions in the subsequent runs. Note: The importance of randomization cannot be over stressed. Randomization is necessary for conclusions drawn from the experiment to be correct, unambiguous and defensible.
• Regression discontinuity design: A design in which assignment to a treatment is determined at least partly by the value of an observed covariate lying on either side of a fixed threshold.
• Replication: Performing the same treatment combination more than once. Note: Including replication allows an estimate of the random error independent of any lack of fit error.
• Resolution: In fractional factorial designs, "resolution" describes the degree to which the estimated main-effects are aliased (or confounded) with estimated higher-order interactions (2-level interactions, 3-level interactions, etc.). In general, the resolution of a design is one more than the smallest order interaction which is aliased with some main effect. If some main effects are confounded with some 2-level interactions, the resolution is 3. Note: Full factorial designs have no confounding and are said to have resolution "infinity". For most practical purposes, a resolution 5 design is excellent and a resolution 4 design may be adequate. Resolution 3 designs are useful as economical screening designs.
• Response(s): The output(s) of a process. Sometimes called dependent variable(s).
• Response surface: A designed experiment that models the quantitative response, especially for the short-term goal of improving a process and the longer-term goal of finding optimum factor-values. Traditionally, response-surfaces have been modeled with quadratic-polynomials, whose estimation requires that every factor have three levels.
• Rotatability: A design is rotatable if the variance of the predicted response at any point x depends only on the distance of x from the design center point. A design with this property can be rotated around its center point without changing the prediction variance at x. Note: Rotatability is a desirable property for response surface designs (i.e. quadratic model designs).
• Scaling factor levels: Transforming factor levels so that the high value becomes +1 and the low value becomes -1.
• Screening design: A designed experiment that identifies which of many factors have a significant effect on the response. Note: Typically screening designs have more than 5 factors.
• Test plan: a written document that gives a specific listing of the test procedures and sequence to be followed.
• Treatment: A treatment is a specific combination of factor levels whose effect is to be compared with other treatments.
• Treatment combination: The combination of the settings of several factors in a given experimental trial. Also known as a run.
• Treatment group: see Control group
• Variance components: Partitioning of the overall variation into assignable components.

See also

• Glossary of probability and statistics
• Notation in probability and statistics
• List of statistical topics

External links

 This article incorporates public domain material from websites or documents of the National Institute of Standards and Technology.