Pulse compression

Pulse compression is a signal processing technique commonly used by radar, sonar and echography to increase the range resolution as well as the signal to noise ratio. This is achieved by modulating the transmitted pulse and then correlating the received signal with the transmitted pulse.

Simple pulse

Signal description

The simplest signal a pulse radar can transmit is a sinusoidal pulse of amplitude, $A$ and carrier frequency, $f_0$, truncated by a rectangular function of width, $\scriptstyle T$. The pulse is transmitted periodically, but that is not the main topic of this article; we will consider only a single pulse, $s$. If we assume the pulse to start at time $t\,=\,0$, the signal can be written the following way, using the complex notation:

$s(t) = \left\{ \begin{array}{ll} A e^{2 i \pi f_0 t} &\text{if} \; 0 \leq t < T \\ 0 &\text{otherwise} \end{array}\right.$

Range resolution

Let us determine the range resolution which can be obtained with such a signal. The return signal, written $\scriptstyle r(t)$, is an attenuated and time-shifted copy of the original transmitted signal (in reality, Doppler effect can play a role too, but this is not important here.) There is also noise in the incoming signal, both on the imaginary and the real channel, which we will assume to be white and Gaussian (this generally holds in reality); we write $\scriptstyle B(t)$ to denote that noise. To detect the incoming signal, matched filtering is commonly used. This method is optimal when a known signal is to be detected among additive white Gaussian noise.

In other words, the cross-correlation of the received signal with the transmitted signal is computed. This is achieved by convolving the incoming signal with a conjugated and time-reversed version of the transmitted signal. This operation can be done either in software or with hardware. We write $\scriptstyle <s,\,r>(t)$ for this cross-correlation. We have:

$\langle s,r \rangle (t) = \int_{t'\,=\,0}^{+\infty} s^\star(t')r(t+t') dt'$

If the reflected signal comes back to the receiver at time $\scriptstyle t_r$ and is attenuated by factor $\scriptstyle K$, this yields:

$r(t)= \left\{ \begin{array}{ll} K A e^{2 i \pi f_0 (t\,-\,t_r)} +B(t) &\mbox{if} \; t_r \leq t < t_r+T \\ B(t) &\mbox{otherwise}\end{array}\right.$

Since we know the transmitted signal, we obtain:

$\langle s,r \rangle (t) = KA^2\Lambda\left (\frac{t-t_r}{T} \right)e^{2 i \pi f_0 (t\,-\,t_r)} + B'(t)$

where $\scriptstyle B'(t)$, the result of the intercorrelation between the noise and the transmitted signal. Function $\Lambda$ is the triangle function, its value is 0 on $\scriptstyle [-\infty,\, -\frac{1}{2}] \,\cup\, [\frac{1}{2}, \,+\infty]$, it increases linearly on $\scriptstyle [-\frac{1}{2},\, 0]$ where it reaches its maximum 1, and it decreases linearly on $\scriptstyle [0,\,\frac{1}{2}]$ until it reaches 0 again. Figures at the end of this paragraph show the shape of the intercorrelation for a sample signal (in red), in this case a real truncated sine, of duration $\scriptstyle T\,=\,1$ seconds, of unit amplitude, and frequency $\scriptstyle f_0\,=\,10$ hertz. Two echoes (in blue) come back with delays of 3 and 5 seconds and amplitudes equal to 0.5 and 0.3 times the amplitude of the transmitted pulse, respectively; these are just random values for the sake of the example. Since the signal is real, the intercorrelation is weighted by an additional ​¹⁄₂ factor.

If two pulses come back (nearly) at the same time, the intercorrelation is equal to the sum of the intercorrelations of the two elementary signals. To distinguish one "triangular" envelope from that of the other pulse, it is clearly visible that the times of arrival of the two pulses must be separated by at least $\scriptstyle T$ so that the maxima of both pulses can be separated. If this condition is not met, both triangles will be mixed together and impossible to separate.

Since the distance travelled by a wave during $\scriptstyle T$ is $\scriptstyle cT$ (where c is the speed of the wave in the medium), and since this distance corresponds to a round-trip time, we get:

 

Result 1
The range resolution with a sinusoidal pulse is $\scriptstyle \frac{1}{2}cT$ where $\scriptstyle T$ is the pulse Duration and, $\scriptstyle c$, the speed of the wave. Conclusion: to increase the resolution, the pulse length must be reduced.

 

Example (simple impulsion): transmitted signal in red (carrier 10 hertz, amplitude 1, duration 1 second) and two echoes (in blue).

Before matched filtering	After matched filtering
File:Two targets before.jpg If the targets are separated enough...	File:Two targets resoluted.jpg ...echoes can be distinguished.
File:Two targets below resolution before.jpg If the targets are too close...	File:Two targets below resolution.jpg ...the echoes are mixed together.

Required energy to transmit that signal

The instantaneous power of the transmitted pulse is $\scriptstyle P(t)\,=\,|s|^2(t)$. The energy put into that signal is:

$E = \int_0^T P(t)dt = A^2 T$

Similarly, the energy in the received pulse is $\scriptstyle E_r \,=\, K^2 A^2 T$. If $\scriptstyle\sigma$ is the standard deviation of the noise, the signal-to-noise ratio (SNR) at the receiver is:

$SNR = \frac{E_r}{\sigma^{2}} = \frac{K^2 A^2 T}{\sigma^{2}}$

The SNR is proportional to pulse duration $T$, if other parameters are held constant. This introduces a tradeoff: increasing $T$ improves the SNR, but reduces the resolution, and vice versa.

Pulse compression by linear frequency modulation (or chirping)

Basic principles

How can one have a large enough pulse (to still have a good SNR at the receiver) without poor resolution? This is where pulse compression enters the picture. The basic principle is the following:

• a signal is transmitted, with a long enough length so that the energy budget is correct
• this signal is designed so that after matched filtering, the width of the intercorrelated signals is smaller than the width obtained by the standard sinusoidal pulse, as explained above (hence the name of the technique: pulse compression).

In radar or sonar applications, linear chirps are the most typically used signals to achieve pulse compression. The pulse being of finite length, the amplitude is a rectangle function. If the transmitted signal has a duration $\scriptstyle T$, begins at $\scriptstyle t \,=\, 0$ and linearly sweeps the frequency band $\scriptstyle \Delta f$ centered on carrier $\scriptstyle f_0$, it can be written:

$s_c(t) = \left\{ \begin{array}{ll} A e^{i 2 \pi \left( \left( f_0 \,-\, \frac{\Delta f}{2}\right) t \, + \, \frac{\Delta f}{2T}t^2 \, \right)} &\mbox{if} \; 0 \leq t < T \\ 0 &\mbox{otherwise}\end{array}\right.$

The chirp definition above means that the phase of the chirped signal (that is, the argument of the complex exponential), is the quadratic:

$\phi(t) = 2\pi \left( \left( f_0 \,-\, \frac{\Delta f}{2}\right) t \, + \, \frac{\Delta f}{2T}t^2 \, \right)$

thus the instantaneous frequency is (by definition):

$f(t) = \frac{1}{2\pi}\left[\frac{d\phi}{dt}\right ]_t = f_0-\frac{\Delta f}{2}+\frac{\Delta f}{T}t$

which is the intended linear ramp going from $\scriptstyle f_0 \,-\, \frac{\Delta f}{2}$ at $\scriptstyle t \,=\, 0$ to $\scriptstyle f_0 \,+\, \frac{\Delta f}{2}$ at $\scriptstyle t \,=\, T$.

The relation of phase to frequency is often used in the other direction, starting with the desired $f(t)$ and writing the chirp phase via the integration of frequency:

$\phi(t) = 2 \pi \int_0^t f(u)\,du$

Cross-correlation between the transmitted and the received signal

As for the "simple" pulse, let us compute the cross-correlation between the transmitted and the received signal. To simplify things, we shall consider that the chirp is not written as it is given above, but in this alternate form (the final result will be the same):

$s_{c'}(t) = \left\{ \begin{array}{ll} A e^{2 i \pi \left (f_0 \,+\, \frac{\Delta f}{2T}t\right) t} &\mbox{if}\; -\frac{T}{2} \leq t < \frac{T}{2} \\ 0 &\mbox{otherwise}\end{array}\right.$

Since this cross-correlation is equal (save for the $K$ attenuation factor), to the autocorrelation function of $\scriptstyle s_{c'}$, this is what we consider:

$\langle s_{c'},s_{c'}\rangle (t) = \int_{-\infty}^{+\infty}s_{c'}^\star(-t')s_{c'}(t-t')dt'$

It can be shown that the autocorrelation function of $s_{c'}$ is:

$\langle s_{c'}, s_{c'}\rangle(t) = A^2T \Lambda \left(\frac{t}{T} \right) \mathrm{sinc} \left[ \pi \Delta f t \Lambda \left( \frac{t}{T}\right) \right] e^{2 i \pi f_0 t}$

The maximum of the autocorrelation function of $\scriptstyle s_{c'}$ is reached at 0. Around 0, this function behaves as the sinc (or cardinal sine) term. The −3 dB temporal width of that cardinal sine is more or less equal to $\scriptstyle T' \,=\, \frac{1}{\Delta f}$. Everything happens as if, after matched filtering, we had the resolution that would have been reached with a simple pulse of duration $\scriptstyle T'$. For the common values of $\scriptstyle \Delta f$, $\scriptstyle T'$ is smaller than $\scriptstyle T$, hence the pulse compression name.

Since the cardinal sine can have annoying sidelobes, a common practice is to filter the result by a window (Hamming, Hann, etc.). In practice, this can be done at the same time as the adapted filtering by multiplying the reference chirp with the filter. The result will be a signal with a slightly lower maximum amplitude, but the sidelobes will be filtered out, which is more important.

Result 2
The distance resolution reachable with a linear frequency modulation of a pulse on a bandwidth $\scriptstyle \Delta f$ is: $\scriptstyle \frac{c}{2\Delta f}$ where $\scriptstyle c$ is the speed of the wave.

 

Definition
Ratio $\scriptstyle \frac{T}{T^\prime} \,=\, T\Delta f$ is the pulse compression ratio. It is generally greater than 1 (usually, its value is 20 to 30).

 

Example (chirped pulse): transmitted signal in red (carrier 10 hertz, modulation on 16 hertz, amplitude 1, duration 1 second) and two echoes (in blue).

File:Chirp before.jpg Before matched filtering

File:Chirp compr.jpg After matched filtering: the echoes are shorter in time.

Improving the SNR through pulse compression

The energy of the signal does not vary during pulse compression. However, it is now located in the main lobe of the cardinal sine, whose width is approximately $\scriptstyle T' \,\approx\, \frac{1}{\Delta f}$. If $\scriptstyle P$ is the power of the signal before compression, and $\scriptstyle P'$ the power of the signal after compression, we have:

$P\times T = P' \times T'$

which yields:

$P'= P\times \frac{T}{T'}$

Besides, the power of the noise does not change through intercorrelation since it is not correlated to the transmitted pulse (it is totally random). As a consequence:  

Result 3
After pulse compression, the power of the received signal can be considered as being amplified by $\scriptstyle T \Delta f$. This additional gain can be injected in the radar equation.

 

Example: same signals as above, plus an additive Gaussian white noise ($\scriptstyle \sigma \,=\, 0.5$)

File:Chirp noise.jpg Before matched filtering: the signal is hidden in noise

File:Chirp compr noise.jpg After matched filtering: echoes become visible.

Pulse compression by phase coding

There are other means to modulate the signal. Phase modulation is a commonly used technique; in this case, the pulse is divided in $\scriptstyle N$ time slots of duration $\scriptstyle \frac{T}{N}$ for which the phase at the origin is chosen according to a pre-established convention. For instance, it is possible to not change the phase for some time slots (which comes down to just leaving the signal as it is, in those slots) and de-phase the signal in the other slots by $\scriptstyle \pi$ (which is equivalent of changing the sign of the signal). The precise way of choosing the sequence of $\scriptstyle \{0,\, \pi \}$ phases is done according to a technique known as Barker codes. It is possible to code the sequence on more than two phases (polyphase coding). As with a linear chirp, pulse compression is achieved through intercorrelation.

The advantages of the Barker codes are their simplicity (as indicated above, a $\scriptstyle \pi$ de-phasing is a simple sign change), but the pulse compression ratio is lower than in the chirp case and the compression is very sensitive to frequency changes due to the Doppler effect if that change is larger than $\scriptstyle \frac{1}{T}$.

Further reading

• Nadav Levanon, and Eli Mozeson. Radar signals. Wiley. com, 2004.
• Hao He, Jian Li, and Petre Stoica. Waveform design for active sensing systems: a computational approach. Cambridge University Press, 2012.
• M. Soltanalian. Signal Design for Active Sensing and Communications. Uppsala Dissertations from the Faculty of Science and Technology (printed by Elanders Sverige AB), 2014.
• Solomon W. Golomb, and Guang Gong. Signal design for good correlation: for wireless communication, cryptography, and radar. Cambridge University Press, 2005.
• Fulvio Gini, Antonio De Maio, and Lee Patton, eds. Waveform design and diversity for advanced radar systems. Institution of engineering and technology, 2012.
• John J. Benedetto, Ioannis Konstantinidis, and Muralidhar Rangaswamy. "Phase-coded waveforms and their design." IEEE Signal Processing Magazine, 26.1 (2009): 22-31.
• Ducoff, Michael R., and Byron W. Tietjen. "Pulse compression radar." Radar Handbook (2008): 8-3.

See also

• Spread spectrum
• Chirp compression