Spray nozzle

A spray nozzle is a precision device that facilitates dispersion of liquid into a spray. Nozzles are used for three purposes: to distribute a liquid over an area, to increase liquid surface area, and create impact force on a solid surface. A wide variety of spray nozzle applications use a number of spray characteristics to describe the spray.

Spray nozzles can be categorized based on the energy input used to cause atomization, the breakup of the fluid into drops. Spray nozzles can have one or more outlets; a multiple outlet nozzle is known as a compound nozzle.

Single-fluid nozzle

Single-fluid or hydraulic spray nozzles utilize the kinetic energy of the liquid to break it up into droplets. This most widely used type of spray nozzle is more energy efficient at producing surface area than most other types. As the fluid pressure increases, the flow through the nozzle increases, and the drop size decreases. Many configurations of single fluid nozzles are used depending on the spray characteristics desired.

Plain-orifice nozzle

The simplest single fluid nozzle is a plain orifice nozzle as shown in the diagram. This nozzle often produces little if any atomization, but directs the stream of liquid. If the pressure drop is high, at least 25 bars (2,500 kPa), the material is often finely atomized, as in a diesel injector. At lower pressures, this type of nozzle is often used for tank cleaning, either as a fixed position compound spray nozzle or as a rotary nozzle.

• Plain orifice nozzle.png

  Plain orifice spray nozzle

Shaped-orifice nozzle

The shaped orifice uses a hemispherical shaped inlet and a V notched outlet to cause the flow to spread out on the axis of the V notch. A flat fan spray results which is useful for many spray applications, such as spray painting.

• Flat fan nozzle.png

  Flat fan spray pattern spray nozzle

Surface-impingement single-fluid nozzle

A surface impingement nozzle causes a stream of liquid to impinge on a surface resulting in a sheet of liquid that breaks up into drops. This flat fan spray pattern nozzle is used in many applications ranging from applying agricultural herbicides to row crop to painting.

The impingement surface can be formed in a spiral to yield a spiral shaped sheet approximating a full cone spray pattern or a hollow-cone spray pattern.

The spiral design generally produces a smaller drop size than pressure swirl type nozzle design, for a given pressure and flow rate. This design is clog resistant due to the large free passage.

Common applications include gas scrubbing applications (e.g., flue-gas desulfurization where the smaller droplets often offer superior performance) and fire fighting (where the mix of droplet densities allow spray penetration through strong thermal currents).

• Impg nozzle.png

  Surface impingement spray nozzle

• Spiral impingement nozzle.png

  Spiral spray nozzle

Pressure-swirl single-fluid spray nozzle

Pressure-swirl spray nozzles are high-performance (small drop size) devices with one configuration shown. The stationary core induces a rotary fluid motion which causes the swirling of the fluid in the swirl chamber. A film is discharged from the perimeter of the outlet orifice producing a characteristic hollow cone spray pattern. Air or other surrounding gas is drawn inside the swirl chamber to form an air core within the swirling liquid. Many configurations of fluid inlets are used to produce this hollow cone pattern depending on the nozzle capacity and materials of construction. The uses of this nozzle include evaporative cooling and spray drying.

• Swirl nozzle.png

  Pressure swirl spray nozzle

• Spillback Nozzle.jpg

  Spillback Nozzle

Solid-cone single-fluid nozzle

One of the configurations of the solid cone spray nozzle is shown in a schematic diagram. A swirling liquid motion is induced with the vane structure, however; the discharge flow fills the entire outlet orifice. For the same capacity and pressure drop, a full cone nozzle will produce a larger drop size than a hollow cone nozzle. The coverage is the desired feature for such a nozzle, which is often used for applications to distribute fluid over an area.

Compound nozzle

A compound nozzle is a type of nozzle in which several individual single or two fluid nozzles are incorporated into one nozzle body, as shown below. This allows design control of drop size and spray coverage angle.

• Compound nozzle.png

  Compound pressure swirl spray nozzle with wide pattern

Two-fluid nozzles

Two-fluid nozzles atomize by causing the interaction of high velocity gas and liquid. Compressed air is most often used as the atomizing gas, but sometimes steam or other gases are used. The many varied designs of two-fluid nozzles can be grouped into internal mix or external mix depending on the mixing point of the gas and liquid streams relative to the nozzle face.

Internal-mix two-fluid nozzles

Internal mix nozzles contact fluids inside the nozzle; one configuration is shown in the figure above. Shearing between high velocity gas and low velocity liquid disintegrates the liquid stream into droplets, producing a high velocity spray. This type of nozzle tends to use less atomizing gas than an external mix atomizer and is better suited to higher viscosity streams. Many compound internal-mix nozzles are commercially used; e.g., for fuel oil atomization.

External-mix two-fluid nozzles

External mix nozzles contacts fluids outside the nozzle as shown in the schematic diagram. This type of spray nozzle may require more atomizing air and a higher atomizing air pressure drop because the mixing and atomization of liquid takes place outside the nozzle. The liquid pressure drop is lower for this type of nozzle, sometimes drawing liquid into the nozzle due to the suction caused by the atomizing air nozzles (siphon nozzle). If the liquid to be atomized contains solids an external mix atomizer may be preferred. This spray may be shaped to produce different spray patterns. A flat pattern is formed with additional air ports to flatten or reshape the circular spray cross-section discharge.

Control of two-fluid nozzles

Many applications use two-fluid nozzles to achieve a controlled small drop size over a range of operation. Each nozzle has a performance curve, and the liquid and gas flow rates determine the drop size. Excessive drop size can lead to catastrophic equipment failure or may have an adverse effect on the process or product. For example, the gas conditioning tower in a cement plant often utilizes evaporative cooling caused by water atomized by two-fluid nozzles into the dust laden gas. If drops do not completely evaporate and strike a vessel wall dust will accumulate, resulting in the potential for flow restriction in the outlet duct, disrupting the plant operation.

• IMTF wiki.png

  Internal mix two-fluid spray nozzle

• EM TF wiki.png

  External mix two-fluid spray nozzle

• Laval Nozzle.JPG

  TwinFluid Nozzle

Rotary atomizers

Rotary atomizers use a high speed rotating disk, cup or wheel to discharge liquid at high speed to the perimeter, forming a hollow cone spray. The rotational speed controls the drop size. Spray drying and spray painting are the most important and common uses of this technology.

Ultrasonic atomizers

Main article: Ultrasonic nozzle

This type of spray nozzle utilizes high frequency (20–180 kHz) vibration to produce narrow drop-size distribution and low velocity spray from a liquid. The vibration of a piezoelectric crystal causes capillary waves on the nozzle surface liquid film. An Ultrasonic nozzle can be key to high transfer efficiency and process stability as they are very hard to clog. They are particularly useful in medical device coatings for their reliability.

• How Ultrasonic Spray Nozzles Work.oggtheora.ogv

  How ultrasonic spray nozzles work.

Electrostatic

Electrostatic charging of sprays is very useful for high transfer efficiency. Examples are the industrial spraying of coatings (paint) and applying lubricant oils. The charging is at high voltage (20–40 kV) but low current.

Nozzle performance factors

Liquid properties

Almost all drop size data supplied by nozzle manufacturers are based on spraying water under laboratory conditions, . The effect of liquid properties should be understood and accounted for when selecting a nozzle for a process that is drop size sensitive.

Temperature

Liquid temperature changes do not directly affect nozzle performance, but can affect viscosity, surface tension, and specific gravity, which can then influence spray nozzle performance.

Specific gravity

Specific gravity is the ratio of the mass of a given volume of liquid to the mass of the same volume of water. In spraying, the main effect of the specific gravity Sg of a liquid other than water is on the capacity of the spray nozzle. All vendor-supplied performance data for nozzles are based on spraying water. To determine the volumetric flowrate Q, of a liquid other than water the following equation should be used.

${Q_f} = {Q_{water}}\sqrt \frac{1}{Sg}$

Viscosity

Dynamic viscosity is defined as the property of a liquid that resists change in the shape or arrangement of its elements during flow. Liquid viscosity primarily affects spray pattern formation and drop size. Liquids with a high viscosity require a higher minimum pressure to begin spray pattern formation and yield narrower spray angles compared to water.

Surface tension

The surface tension of a liquid tends to assume the smallest possible size, acting as a membrane under tension. Any portion of the liquid surface exerts a tension upon adjacent portions or upon other objects that it contacts. This force is in the plane of the surface, and its amount per unit of length is surface tension. The value for water is about 0.073 N/m at 21 °C. The main effects of surface tension are on minimum operating pressure, spray angle, and drop size. Surface tension is more apparent at low operating pressures. A higher surface tension reduces the spray angle, particularly on hollow cone nozzles. Low surface tensions can allow nozzles to be operated at lower pressures.

Nozzle wear

Nozzle wear is indicated by an increase in nozzle capacity and by a change in the spray pattern, in which the distribution (uniformity of spray pattern) deteriorates and increases drop size. Choice of a wear resistant material of construction increases nozzle life. Because many single fluid nozzles are used to meter flows, worn nozzles result in excessive liquid usage.

Material of construction

The material of construction is selected based on the fluid properties of the liquid that is to be sprayed and the environment surrounding the nozzle. Spray nozzles are most commonly fabricated from metals, such as brass, Stainless steel, and nickel alloys, but plastics such as PTFE and PVC and ceramics (alumina and silicon carbide) are also used. Several factors must be considered, including erosive wear, chemical attack, and the effects of high temperature.

Applications

Further information: Spray (liquid drop)

See also

• Nozzle
• Nebulizer
• Pesticide application
• Ilass Institute for Liquid Atomization and Spray Systems