Van 't Hoff equation

From Infogalactic: the planetary knowledge core
(Redirected from Van 't Hoff plot)
Jump to: navigation, search

The Van 't Hoff equation in chemical thermodynamics relates the change in the equilibrium constant, Keq, of a chemical reaction to the change in temperature, T, given the standard enthalpy change, ΔHo, for the process. It was proposed by Dutch chemist Jacobus Henricus van 't Hoff in 1884.[1]

The Van 't Hoff equation has been widely utilized to explore the changes in state functions in a thermodynamic system. The Van 't Hoff plot, which is derived from this equation, is especially effective in estimating the change in enthalpy, or total energy, and entropy, or amount of disorder, of a chemical reaction.

Equation

Under standard conditions

Under standard conditions, the Van 't Hoff equation is[2][3]

 \frac{d \ln K_{eq}}{dT} = \frac{\Delta H^\ominus}{RT^2},

where R is the Ideal gas constant. This equation is exact at any one temperature. In practice, the equation is often integrated between two temperatures under the assumption that the reaction enthalpy ΔH is constant. Since in reality ΔH as well as ΔS do vary with temperature for most processes,[4] the integrated equation is only approximate.

A major use of the integrated equation is to estimate a new equilibrium constant at a new absolute temperature assuming a constant standard enthalpy change over the temperature range.

To obtain the integrated equation, it is convenient to first rewrite the van't Hoff equation as[2]

 \frac{d \ln K_{eq}}{d {\frac{{1 }}{{T }}}} = -\frac{\Delta H^\ominus}{R}.

The definite integral between temperatures T1 and T2 is then

\ln \left( {\frac{{K_2 }}{{K_1 }}} \right) =  \frac{{\ - \Delta H^\ominus }}{R}\left( {\frac{1}{{T_2 }} - \frac{1}{{T_1 }}} \right).

In this equation K1 is the equilibrium constant at absolute temperature T1, and K2 is the equilibrium constant at absolute temperature T2.

Development from thermodynamics

From the definition of Gibbs free energy

 \Delta G^\ominus = \Delta H^\ominus - T\Delta S^\ominus

where S is the entropy of the system, and from the Gibbs free energy isotherm equation, [5] and

\Delta G^\ominus = -RT \ln K_{eq}

These equations are combined to obtain

\ln K_{eq} = - \frac{{\Delta H^\ominus}}{RT}+  \frac{{\Delta S^\ominus }}{R}.

Differentiation of this expression with respect to the variable T yields the Van 't Hoff equation.

Provided that ΔHo and ΔSo are constant, the preceding equation gives ln K as a linear function of 1/T, and is known as the linear form of the Van't Hoff equation. Therefore, when the range in temperature is small enough that the standard enthalpy and entropy changes are essentially constant, a plot of the natural logarithm of the equilibrium constant versus the reciprocal temperature gives a straight line. The slope of the line may be multiplied by the gas constant R to obtain the standard enthalpy change of the reaction, and the intercept may be multiplied by R to obtain the standard entropy change.

Van 't Hoff isotherm

The Gibbs free energy can change with the change of the temperature and pressure of the thermodynamic system. The Van 't Hoff isotherm can be used to determine the Gibbs free energy for non-standard state reactions at a constant temperature:[6]

\left(\frac {dG}{d\xi}\right)_{T,p} = \Delta_rG + RT \ln Q_r~

where \Delta_rG is the Gibbs free energy for the reaction, and Q_r~ is the reaction quotient. When a reaction is at equilibrium, Q_r~=K_{eq}. The Van 't Hoff isotherm can help estimate the equilibrium reaction shift. When \Delta_rG<0, the reaction moves in the forward direction. When \Delta_rG>0, the reaction moves in the backwards directions. See Chemical equilibrium.

Van 't Hoff plot

For a reversible reaction, the equilibrium constant can be measured at a variety of temperatures. This data can be plotted on a graph with \ln K_{eq} on the Y-axis and 1/T on the X-axis. The data should have a linear relationship, the equation for which can be found by fitting the data using the linear form of the Van 't Hoff equation

\ln K_{eq} = - \frac{{\Delta H^\ominus}}{RT}+  \frac{{\Delta S^\ominus }}{R}.

This graph is called the Van 't Hoff plot and is widely used to estimate the enthalpy and entropy of a chemical reaction. From this plot, -\frac{\Delta H}{R} is the slope and \frac{\Delta S}{R} is the intercept of the linear fit.

By measuring the equilibrium constant, Keq, at different temperatures, the Van 't Hoff plot can be used to assess a reaction when temperature changes.[7][8] Knowing the slope and intercept from the Van 't Hoff plot, the enthalpy and entropy of a reaction can be easily obtained using

\Delta H = - R * slope,

\Delta S = R * intercept.

The Van 't Hoff plot can be used to quickly determine the enthalpy of a chemical reaction both qualitatively and quantitatively. Change in enthalpy can be positive or negative, leading to two major forms of the Van 't Hoff plot.

Endothermic reactions

File:Endothermic Reaction van't Hoff Plot.png
Endothermic Reaction Van 't Hoff Plot

For an endothermic reaction, heat is absorbed, making the net enthalpy change positive. Thus, according to the definition of the slope:

Slope= -\frac{\Delta H}{R}

for an endothermic reaction,

\Delta H > 0 and R is the gas constant

So

Slope= -\frac{\Delta H}{R} < 0

Thus, for an endothermic reaction, the Van 't Hoff plot should always have a negative slope.

Exothermic reactions

File:Exothermic Reaction van't Hoff Plot.png
Exothermic Reaction Van 't Hoff Plot

For an exothermic reaction, heat is released, making the net enthalpy change negative. Thus, according to the definition of the slope:

Slope= -\frac{\Delta H}{R}

from an exothermic reaction,

\Delta H < 0 and R is the gas constant

So

Slope= -\frac{\Delta H}{R} > 0

Thus, for an exothermic reaction, the Van 't Hoff plot should always have a positive slope.

Error propagation

Using the fact that ΔG0 = -RTlnK = ΔH0 - TΔS0 it would appear that two measurements of K would suffice to be able to obtain a value of ΔH0:

ΔH0 = 2.303 R (logK1 - logK2)/(1/T2-1/T1),

where K1 and K2 are the equilibrium constant values obtained at temperatures T1 and T2 respectively. The precision of ΔH0 values obtained in this way is highly dependent on the precision of the equilibrium constant values. A typical pair of temperatures might be 25 and 35°C. For these temperatures (1/T2-1/T1) = (1/298 -1/308) = 1.1×10−4 K. Inserting this value into the expression for ΔH0

ΔH0 = 175000 (logK1 - logK2) (J mol−1}

Now, error propagation shows that the error on ΔH0 will be 175000 J mol−1 times the error on logK1 - logK2. Thus the error is magnified by a factor of about 175 in the kJ mol−1 units in which ΔH is normally expressed. Assume for example that the error on each logK, σ, is about 0.02, a small but reasonable value. The error on logK1 - logK2 will be of the order of √2σ, ~0.03 and the error on ΔH0 will be about 5 kJ mol−1. So, even though the individual stability constants were determined with good precision the enthalpy calculated in this way is subject to a significant error.

The entropy will then be obtained from ΔS0 = (ΔH0 + RTlnK)/T. In this expression the error on the second term is negligible compared to the error on the first term. The magnifying factor is then 175000 J mol−1/298 K, so for an error of 0.03 in the ratio of logarithms the error on ΔS0 will be of the order of 17.5 JK−1mol−1.

When equilibrium constants are measured at three or more temperatures values of ΔH0 will be obtained by straight line fitting. In this case the error on the standard enthalpy will be magnified to a somewhat lesser, but still substantial, extent.

Applications of the Van 't Hoff plot

Van 't Hoff analysis

File:Van't Hoff analysis.png
Van 't Hoff analysis

In biological research, the Van 't Hoff plot is also called Van 't Hoff analysis.[9] It's most effective in determining the favored product in a reaction.

Assume two products B and C form in a reaction:

\mathrm{a\ A + d\ D \longrightarrow b\ B}

\mathrm{a\ A + d\ D \longrightarrow c\ C}

In this case, K_{eq} can be defined as ratio of B to C rather than the equilibrium constant.

When \frac {B}{C} >1 , B is the favored product, and the data on the Van 't Hoff plot will be in the positive region.

When \frac {B}{C} <1 , C is the favored product, and the data on the Van 't Hoff plot will be in the negative region.

Using this information, a Van 't Hoff analysis can help determine the most suitable temperature for a favored product.

Recently, a Van 't Hoff analysis was used to determine whether water preferentially forms a hydrogen bond with the C-terminus or the N-terminus of the amino acid proline.[10] The equilibrium constant for each reaction was found at a variety of temperatures, and a Van 't Hoff plot was created. This analysis showed that enthalpically, the water preferred to hydrogen bond to the C-terminus, but entropically it was more favorable to hydrogen bond with the N-terminus. Specifically, they found that C-terminus hydrogen bonding was favored by 4.2-6.4 kJ/mol. The N-terminus hydrogen bonding was favored by 31-43 J/(mol K).

This data alone could not conclude which site water will preferentially hydrogen bond to, so additional experiments were used. It was determined that at lower temperatures, the enthalpically favored species, the water hydrogen bonded to the C-terminus, was preferred. At higher temperatures, the entropically favored species, the water hydrogen bonded to the N-terminus, was preferred.

Mechanistic studies

File:Van't Hoff plot in Mechanism study.png
Van 't Hoff plot in Mechanism study

A chemical reaction may undergo different reaction mechanisms under different temperatures.[11]

In this case, a Van 't Hoff plot with two or more linear fits may be exploited. Each linear fit has a different slope and intercept which indicates different changes in enthalpy and entropy for each distinct mechanisms. The Van 't Hoff plot can be used to find the enthalpy and entropy change for each mechanism and the favored mechanism under different temperatures.

\Delta H_1 = - R * slope_1,

\Delta S_1 = R * interception_1;

\Delta H_2 = - R * slope_2,

\Delta S_2 = R * interception_2;

In the example figure, the reaction undergoes mechanism 1 at high temperature and mechanism 2 at low temperature.

Temperature dependence

File:Temperature dependence van't Hoff plot.png
Temperature dependent Van 't Hoff plot

The Van 't Hoff plot is linear based on the assumption that the enthalpy and entropy are constant with temperature changes. However, in some cases the enthalpy and entropy do change dramatically with temperature. A first order approximation is to assume that the two different reaction products have different heat capacities. Incorporating this assumption yields an additional term, \frac {c}{T^2} , in the expression for the equilibrium constant as a function of temperature. A polynomial fit can then be used to analyze data which has exhibits a non-constant standard enthalpy of reaction:[12]

ln K_{eq} = a+ \frac {b}{T} + \frac {c}{T^2} ,

where

\Delta H = - R * (b+2\frac {c}{T}),

\Delta S = R * (a-\frac {c}{T^2}).

Thus, the enthalpy and entropy of a reaction can still be determined at specific temperatures even when a temperature dependence exists.

See also

References

  1. Biography on Nobel prize website. Nobelprize.org (1911-03-01). Retrieved on 2013-11-8.
  2. 2.0 2.1 Lua error in package.lua at line 80: module 'strict' not found.
  3. Chemical Thermodynamics, D.J.G. Ives, University Chemistry, Macdonald Technical and Scientific, 1971, ISBN 0-356-03736-3
  4. Lua error in package.lua at line 80: module 'strict' not found.
  5. Chemistry, Matter, and the Universe, R.E. Dickerson, I. Geis, W.A. Benjamin Inc. (USA), 1976, ISBN 0-19-855148-7
  6. Lua error in package.lua at line 80: module 'strict' not found.
  7. Lua error in package.lua at line 80: module 'strict' not found.
  8. Lua error in package.lua at line 80: module 'strict' not found.
  9. Lua error in package.lua at line 80: module 'strict' not found.
  10. Lua error in package.lua at line 80: module 'strict' not found.
  11. Lua error in package.lua at line 80: module 'strict' not found.
  12. Lua error in package.lua at line 80: module 'strict' not found.