Vapor pressure

From Infogalactic: the planetary knowledge core
Jump to: navigation, search
The picture shows the particle transition, as a result of their vapor pressure, from the liquid phase to the gas phase and converse.

Vapor pressure or equilibrium vapor pressure is defined as the pressure exerted by a vapor in thermodynamic equilibrium with its condensed phases (solid or liquid) at a given temperature in a closed system. The equilibrium vapor pressure is an indication of a liquid's evaporation rate. It relates to the tendency of particles to escape from the liquid (or a solid). A substance with a high vapor pressure at normal temperatures is often referred to as volatile. The pressure exhibited by vapor present above a liquid surface is known as vapor pressure. As the temperature of a liquid increases, the kinetic energy of its molecules also increases. As the kinetic energy of the molecules increases, the number of molecules transitioning into a vapor also increases, thereby increasing the vapor pressure.

The vapor pressure of any substance increases non-linearly with temperature according to the Clausius–Clapeyron relation. The atmospheric pressure boiling point of a liquid (also known as the normal boiling point) is the temperature at which the vapor pressure equals the ambient atmospheric pressure. With any incremental increase in that temperature, the vapor pressure becomes sufficient to overcome atmospheric pressure and lift the liquid to form vapor bubbles inside the bulk of the substance. Bubble formation deeper in the liquid requires a higher pressure, and therefore higher temperature, because the fluid pressure increases above the atmospheric pressure as the depth increases.

The vapor pressure that a single component in a mixture contributes to the total pressure in the system is called partial pressure. For example, air at sea level, and saturated with water vapor at 20 °C, has partial pressures of about 2.3 kPa of water, 78 kPa of nitrogen, 21 kPa of oxygen and 0.9 kPa of argon.

Measurement and units

Vapor pressure is measured in the standard units of pressure. The International System of Units (SI) recognizes pressure as a derived unit with the dimension of force per area and designates the pascal (Pa) as its standard unit. One pascal is one newton per square meter (N·m−2 or kg·m−1·s−2).

Experimental measurement of vapor pressure is a simple procedure for common pressures between 1 and 200 kPa.[1] Most accurate results are obtained near the boiling point of substances and large errors result for measurements smaller than 1kPa. Procedures often consist of purifying the test substance, isolating it in a container, evacuating any foreign gas, then measuring the equilibrium pressure of the gaseous phase of the substance in the container at different temperatures. Better accuracy is achieved when care is taken to ensure that the entire substance and its vapor are at the prescribed temperature. This is often done, as with the use of an isoteniscope, by submerging the containment area in a liquid bath.

Estimating vapor pressures with Antoine equation

The Antoine equation [2][3] is a mathematical expression of the relation between the vapor pressure and the temperature of pure liquid or solid substances. The basic form of the equation is:

\log P = A-\frac{B}{C+T}

and it can be transformed into this temperature-explicit form:

T = \frac{B}{A-\log P} - C

where: P is the absolute vapor pressure of a substance

    T is the temperature of the substance
    A, B and C are substance-specific coefficients (i.e., constants or parameters)
    \log is typically either \log_{10} or \log_e[3]

A simpler form of the equation with only two coefficients is sometimes used:

\log P = A-\frac{B}{T}

which can be transformed to:

T = \frac{B}{A-\log P}

Sublimations and vaporizations of the same substance have separate sets of Antoine coefficients, as do components in mixtures.[2] Each parameter set for a specific compound is only applicable over a specified temperature range. Generally, temperature ranges are chosen to maintain the equation's accuracy of a few up to 8–10 percent. For many volatile substances, several different sets of parameters are available and used for different temperature ranges. The Antoine equation has poor accuracy with any single parameter set when used from a compound's melting point to its critical temperature. Accuracy is also usually poor when vapor pressure is under 10 Torr because of the limitations of the apparatus used to establish the Antoine parameter values.

The Wagner Equation[4] gives "one of the best"[5] fits to experimental data but is quite complex. It expresses reduced vapor pressure as a function of reduced temperature.

Relation to boiling point of liquids

<templatestyles src="Module:Hatnote/styles.css"></templatestyles>

A log-lin vapor pressure chart for various liquids

As a general trend, vapor pressures of liquids at ambient temperatures increase with decreasing boiling points. This is illustrated in the vapor pressure chart (see right) that shows graphs of the vapor pressures versus temperatures for a variety of liquids.[6]

For example, at any given temperature, methyl chloride has the highest vapor pressure of any of the liquids in the chart. It also has the lowest normal boiling point (−24.2 °C), which is where the vapor pressure curve of methyl chloride (the blue line) intersects the horizontal pressure line of one atmosphere (atm) of absolute vapor pressure.

Although the relation between vapor pressure and temperature is non-linear, the chart uses a logarithmic vertical axis to produce slightly curved lines, so one chart can graph many liquids. A nearly straight line is obtained when the logarithm of the vapor pressure is plotted against 1/(T+230)[7] where T is the temperature in degrees Celsius. The vapor pressure of a liquid at its boiling point equals the pressure of its surrounding environment.

Liquid mixtures

Raoult's law gives an approximation to the vapor pressure of mixtures of liquids. It states that the activity (pressure or fugacity) of a single-phase mixture is equal to the mole-fraction-weighted sum of the components' vapor pressures:

 p_\text{tot} = \sum_i p_i \chi_i \,

where p tot is the mixture's vapor pressure, i is one of the components of the mixture and Χi is the mole fraction of that component in the liquid mixture. The term piΧi is the partial pressure of component i in the mixture. Raoult's Law is applicable only to non-electrolytes (uncharged species); it is most appropriate for non-polar molecules with only weak intermolecular attractions (such as London forces).

Systems that have vapor pressures higher than indicated by the above formula are said to have positive deviations. Such a deviation suggests weaker intermolecular attraction than in the pure components, so that the molecules can be thought of as being "held in" the liquid phase less strongly than in the pure liquid. An example is the azeotrope of approximately 95% ethanol and water. Because the azeotrope's vapor pressure is higher than predicted by Raoult's law, it boils at a temperature below that of either pure component.

There are also systems with negative deviations that have vapor pressures that are lower than expected. Such a deviation is evidence for stronger intermolecular attraction between the constituents of the mixture than exists in the pure components. Thus, the molecules are "held in" the liquid more strongly when a second molecule is present. An example is a mixture of trichloromethane (chloroform) and 2-propanone (acetone), which boils above the boiling point of either pure component.

The negative and positive deviations can be used to determine thermodynamic activity coefficients of the components of mixtures.

Solids

Vapor pressure of liquid and solid benzene

Equilibrium vapor pressure can be defined as the pressure reached when a condensed phase is in equilibrium with its own vapor. In the case of an equilibrium solid, such as a crystal, this can be defined as the pressure when the rate of sublimation of a solid matches the rate of deposition of its vapor phase. For most solids this pressure is very low, but some notable exceptions are naphthalene, dry ice (the vapor pressure of dry ice is 5.73 MPa (831 psi, 56.5 atm) at 20 degrees Celsius, which causes most sealed containers to rupture), and ice. All solid materials have a vapor pressure. However, due to their often extremely low values, measurement can be rather difficult. Typical techniques include the use of thermogravimetry and gas transpiration.

There are a number of methods for calculating the sublimation pressure (i.e., the vapor pressure) of a solid. One method is to estimate the sublimation pressure from extrapolated liquid vapor pressures (of the supercooled liquid), if the heat of fusion is known, by using this particular form of the Clausius–Clapeyron relation:[8]

\ln\,P^S_{solid} = \ln\,P^S_{liquid} - \frac{\Delta H_m}{R} \left( \frac{1}{T} - \frac{1}{T_m} \right)

with:

P^S_{solid} = Sublimation pressure of the solid component at the temperature T<T_m
P^S_{liquid} = Extrapolated vapor pressure of the liquid component at the temperature T<T_m
\Delta H_m = Heat of fusion
R = Gas constant
T = Sublimation temperature
T_m = Melting point temperature

This method assumes that the heat of fusion is temperature-independent, ignores additional transition temperatures between different solid phases, and it gives a fair estimation for temperatures not too far from the melting point. It also shows that the sublimation pressure is lower than the extrapolated liquid vapor pressure (ΔHm is positive) and the difference grows with increased distance from the melting point.

Boiling point of water

Graph of water vapor pressure versus temperature. At the normal boiling point of 100 °C, it equals the standard atmospheric pressure of 760 Torr or 101.325 kPa.

<templatestyles src="Module:Hatnote/styles.css"></templatestyles>

Like all liquids, water boils when its vapor pressure reaches its surrounding pressure. In nature, the atmospheric pressure is lower at higher elevations and water boils at a lower temperature. The boiling temperature of water for atmospheric pressures can be approximated by the Antoine equation:

\log_{10}P = 8.07131 - \frac{1730.63}{233.426 + T_b}

or transformed into this temperature-explicit form:

T_b = \frac{1730.63}{8.07131 - \log_{10}P} - 233.426

where the temperature T_b is the boiling point in degrees Celsius and the pressure P_{ } is in Torr.

Dühring's rule

<templatestyles src="Module:Hatnote/styles.css"></templatestyles>

Dühring's rule states that a linear relationship exists between the temperatures at which two solutions exert the same vapor pressure.

Examples

The following table is a list of a variety of substances ordered by increasing vapor pressure (in absolute units).

Substance Vapor Pressure
(SI units)
Vapor Pressure
(Bar);
Vapor Pressure
(mmHg);
Temperature
Tungsten 100 Pa 0.001 0.75 3203 °C
Ethylene glycol 500 Pa 0.005 3.75 20 °C
Xenon difluoride 600 Pa 0.006 4.50 25 °C
Water (H2O) 2.3 kPa 0.023 17.5 20 °C
Propanol 2.4 kPa 0.024 18.0 20 °C
Ethanol 5.83 kPa 0.0583 43.7 20 °C
Methyl isobutyl ketone 2.66 kPa 0.0266 19.95 25 °C
Freon 113 37.9 kPa 0.379 284 20 °C
Acetaldehyde 98.7 kPa 0.987 740 20 °C
Butane 220 kPa 2.2 1650 20 °C
Formaldehyde 435.7 kPa 4.357 3268 20 °C
Propane[9] 997.8 kPa 9.978 7584 26.85 °C
Carbonyl sulfide 1.255 MPa 12.55 9412 25 °C
Nitrous oxide[10] 5.660 MPa 56.60 42453 25 °C
Carbon dioxide 5.7 MPa 57 42753 20 °C

Estimating vapor pressure from molecular structure

Several empirical methods exist to estimate liquid vapor pressure from molecular structure for organic molecules. Some examples are SIMPOL,[11] the method of Moller et al.,[8] and EVAPORATION.[12][13]

Meaning in meteorology

In meteorology, the term vapor pressure is used to mean the partial pressure of water vapor in the atmosphere, even if it is not in equilibrium,[14] and the equilibrium vapor pressure is specified otherwise. Meteorologists also use the term saturation vapor pressure to refer to the equilibrium vapor pressure of water or brine above a flat surface, to distinguish it from equilibrium vapor pressure, which takes into account the shape and size of water droplets and particulates in the atmosphere.[15]

See also

References

  1. Lua error in package.lua at line 80: module 'strict' not found.
  2. 2.0 2.1 What is the Antoine Equation? (Chemistry Department, Frostburg State University, Maryland)
  3. 3.0 3.1 Lua error in package.lua at line 80: module 'strict' not found.
  4. Lua error in package.lua at line 80: module 'strict' not found.
  5. Perry's Chemical Engineers' Handbook, 7th Ed. pp. 4–15
  6. Lua error in package.lua at line 80: module 'strict' not found.
  7. Lua error in package.lua at line 80: module 'strict' not found.
  8. 8.0 8.1 Lua error in package.lua at line 80: module 'strict' not found.
  9. "Thermophysical Properties Of Fluids II – Methane, Ethane, Propane, Isobutane, And Normal Butane" (page 110 of PDF, page 686 of original document), BA Younglove and JF Ely.
  10. "Thermophysical Properties Of Nitrous Oxide" (page 14 of PDF, page 10 of original document), ESDU.
  11. Lua error in package.lua at line 80: module 'strict' not found.
  12. "Vapour pressure of pure liquid compounds. Estimation by EVAPORATION". tropo.aeronomie.be
  13. Lua error in package.lua at line 80: module 'strict' not found.
  14. Glossary (Developed by the American Meteorological Society)
  15. A Brief Tutorial. jhuapl.edu (An article about the definition of equilibrium vapor pressure)

External links

cs:Sytá pára