Volcanic arc

From Infogalactic: the planetary knowledge core
Jump to: navigation, search
File:Casta Marianas.jpg
Mariana Islands, an oceanic island arc

<templatestyles src="Module:Hatnote/styles.css"></templatestyles>

A volcanic arc is a chain of volcanoes formed above a subducting plate,[1] positioned in an arc shape as seen from above. Offshore volcanoes form islands, resulting in a volcanic island arc. Generally they result from the subduction of an oceanic tectonic plate under another tectonic plate, and often parallel an oceanic trench. The oceanic plate is saturated with water, and volatiles such as water drastically lower the melting point of the mantle. As the oceanic plate is subducted, it is subjected to greater and greater pressures with increasing depth. This pressure squeezes water out of the plate and introduces it to the mantle. Here the mantle melts and forms magma at depth under the overriding plate. The magma ascends to form an arc of volcanoes parallel to the subduction zone.

These should not be confused with hotspot volcanic chains, where volcanoes often form one after another in the middle of a tectonic plate, as the plate moves over the hotspot, and so the volcanoes progress in age from one end of the chain to the other. The Hawaiian Islands form a typical hotspot chain; the older islands (tens of millions of years) to the northwest are smaller and more lush than the recently created (400,000 years ago) Hawaii island itself, which is more rocky. Hot spot volcanoes are also known as "Intra-plate" volcanoes and the islands they create are known as Volcanic Ocean Islands. Volcanic arcs do not generally exhibit such a simple age pattern.

There are two types of volcanic arcs:

  • oceanic arcs form when oceanic crust subducts beneath other oceanic crust on an adjacent plate, creating a volcanic island arc. (Not all island arcs are volcanic island arcs.)
  • continental arcs form when oceanic crust subducts beneath continental crust on an adjacent plate, creating an arc-shaped mountain belt. (Not all mountain belts are formed this way.)

In some situations, a single subduction zone may show both aspects along its length, as part of a plate subducts beneath a continent and part beneath adjacent oceanic crust.

(The term "volcanic arc" is often confused with the term "island arc". The former is a series of volcanoes, but not necessarily offshore. The latter is a series of islands, not necessarily composed solely of volcanoes.)

Volcanoes are present in almost any mountain belt, but this does not make it a volcanic arc. Often there are isolated, but impressively huge volcanoes in a mountain belt. For instance, Vesuvius and the Etna volcanoes in Italy are part of separate but different kinds of mountainous volcanic ensembles.

The active front of a volcanic arc is the belt where volcanism develops at a given time. Active fronts may move over time (millions of years) changing their distance from the oceanic trench as well as their width.

Petrology

In the subduction zone, loss of water from the subducted slab induces partial melting of the overriding mantle and generates low-density, calc-alkaline magma that buoyantly rises to intrude and be extruded through the lithosphere of the overriding plate. This loss of water is due to the destabilization of the mineral chlorite at approximately 40–60 km depth.[2][3] This is the reason for island arc volcanism at consistent distances from the subducting slab: because the temperature-pressure conditions for flux-melting volcanism due to chlorite destabilization will always occur at the same depth, the distance from the trench to the arc volcanoes is determined only by the dip angle of the subducting slab.

On the subducting side of the island arc is a deep and narrow oceanic trench, which is the trace at the Earth’s surface of the boundary between the downgoing and overriding plates. This trench is created by the gravitational pull of the relatively dense subducting plate pulling the leading edge of the plate downward. Multiple earthquakes occur along this subduction boundary with the seismic hypocenters located at increasing depth under the island arc: these quakes define the Wadati-Benioff zones. The volcanic arc forms when the subducting plate reaches a depth of about 100 km.

Ocean basins that are being reduced by subduction are called 'remnant oceans' as they will slowly be shrunken out of existence and crushed in the subsequent orogenic collision. This process has happened over and over in the geologic history of the Earth.

In the rock record, volcanic arcs can be seen as the volcanic rocks themselves, but because volcanic rock is easily weathered and eroded, it is more typical that they are seen as plutonic rocks, the rocks that formed underneath the arc (e.g. the Sierra Nevada batholith), or in the sedimentary record as lithic sandstones.

Examples

Two classic examples of oceanic island arcs are the Mariana Islands in the western Pacific Ocean and the Lesser Antilles in the western Atlantic Ocean. The Cascade Volcanic Arc in western North America and the Andes along the western edge of South America are examples of continental volcanic arcs. The best examples of volcanic arcs with both sets of characteristics are in the North Pacific, with the Aleutian Arc consisting of the Aleutian Islands and their extension the Aleutian Range on the Alaska Peninsula, and the Kuril-Kamchatka Arc comprising the Kuril Islands and southern Kamchatka Peninsula.

Continental arcs

Island arcs

Ancient island arcs

See also

References

  1. Lua error in package.lua at line 80: module 'strict' not found.
  2. Grove, T. L., N. Chatterjee, S. W. Parman, and E. Médard (2006), The Influence of H2O on Mantle Wedge Melting, Earth and Planetary Science Letters, 249, 74-89.
  3. Grove, T.L., C. B. Till, N. Chatterjee, and E. Médard (submitted 2008), Transport of H2O in subduction zones and its role in the formation and location of arc volcanoes, Nature.

he:קשת געשית