Bharat Stage emission standards

Bharat stage emission standards are emission standards instituted by the Government of India to regulate the output of air pollutants from internal combustion engine equipment, including motor vehicles. The standards and the timeline for implementation are set by the Central Pollution Control Board under the Ministry of Environment & Forests and climate change.

The standards, based on European regulations were first introduced in 2000. Progressively stringent norms have been rolled out since then. All new vehicles manufactured after the implementation of the norms have to be compliant with the regulations. Since October 2010, Bharat stage III norms have been enforced across the country. In 13 major cities, Bharat stage IV emission norms have been in place since April 2010.

The phasing out of 2 stroke engine for two wheelers, the stoppage of production of Maruti 800 & introduction of electronic controls have been due to the regulations related to vehicular emissions.

While the norms help in bringing down pollution levels, it invariably results in increased vehicle cost due to the improved technology & higher fuel prices. However, this increase in private cost is offset by savings in health costs for the public, as there is lesser amount of disease causing particulate matter and pollution in the air. Exposure to air pollution can lead to respiratory and cardiovascular diseases, which is estimated to be the cause for 620,000 early deaths in 2010, and the health cost of air pollution in India has been assessed at 3 per cent of its GDP.

Motor vehicles

File:Compare Euro US Indian gasoline emission standards.png

Comparison between European, US, and Bharat Stage (Indian) emission standards for gasoline passenger cars.

File:Compare Euro US Indian diesel emission standards.png

Comparison between European, US, and Bharat Stage (Indian) emission standards for diesel passenger cars. The sizes of the green circles represent the limits for particulate matter.

History

The first emission norms were introduced in India in 1991 for petrol and 1992 for diesel vehicles. These were followed by making the Catalytic converter mandatory for petrol vehicles and the introduction of unleaded petrol in the market.

On 29 April 1999 the Supreme Court of India ruled that all vehicles in India have to meet Euro I or India 2000 norms by 1 June 1999 and Euro II will be mandatory in the NCR by April 2000. Car makers were not prepared for this transition and in a subsequent judgment the implementation date for Euro II was not enforced.

In 2002, the Indian government accepted the report submitted by the Mashelkar committee. The committee proposed a road map for the roll out of Euro based emission norms for India. It also recommended a phased implementation of future norms with the regulations being implemented in major cities first and extended to the rest of the country after a few years.

Based on the recommendations of the committee, the National Auto Fuel policy was announced officially in 2003. The roadmap for implementation of the Bharat Stage norms were laid out till 2010. The policy also created guidelines for auto fuels, reduction of pollution from older vehicles and R&D for air quality data creation and health administration.

Background information

Table 1: Indian Emission Standards (4-Wheel Vehicles)

Standard	Reference	YEAR	Region
India 2000	Euro 1	2000	Nationwide
Bharat Stage II	Euro 2	2001	NCR*, Mumbai, Kolkata, Chennai
		2003.04	NCR*, 13 Cities†
		2005.04	Nationwide
Bharat Stage III	Euro 3	2005.04	NCR*, 13 Cities†
		2010.04	Nationwide
Bharat Stage IV	Euro 4	2010.04	NCR*, 13 Cities†
Bharat Stage V	Euro 5	2017.04 (cancelled)	Entire country
Bharat Stage VI	Euro 6	2020.04 (proposed)	Entire country
* National Capital Region (Delhi) † Mumbai, Kolkata, Chennai, Bengaluru, Hyderabad, Ahmedabad, Pune, Surat, Kanpur, Lucknow, Sholapur, Jamshedpur and Agra

The above standards apply to all new 4-wheel vehicles sold and registered in the respective regions. In addition, the National Auto Fuel Policy introduces certain emission requirements for interstate buses with routes originating or terminating in Delhi or the other 10 cities.

Progress of emission standards for 2-and 3-wheelers:

Table 2: Indian Emission Standards (2 and 3 wheelers)

Standard	Reference	Date
Bharat Stage II	Euro 2	1 April 2005
Bharat Stage III	Euro 3	1 April 2010
Bharat Stage IV	Euro 4	1 April 2012
Bharat Stage V	Euro 5	1 April 2017 (proposed)

In order to comply with the BSIV norms, 2 and 3 wheeler manufacturers will have to fit an evaporative emission control unit, which should lower the amount of fuel that is evaporated when the motorcycle is parked.

Trucks and buses

Exhaust gases from vehicles form a significant portion of air pollution which is harmful to human health and the environment

Emission standards for new heavy-duty diesel engines—applicable to vehicles of GVW > 3,500 kg—are listed in Table 3.

Table 3: Emission Standards for Diesel Truck and Bus Engines, g/kWh

Year	Reference	Test	CO	HC	NOx	PM
1992	–	ECE R49	17.3–32.6	2.7–3.7	–	–
1996	–	ECE R49	11.20	2.40	14.4	–
2000	Euro I	ECE R49	4.5	1.1	8.0	0.36*
2005†	Euro II	ECE R49	4.0	1.1	7.0	0.15
2010†	Euro III	ESC	2.1	0.66	5.0	0.10
		ETC	5.45	0.78	5.0	0.16
2010‡	Euro IV	ESC	1.5	0.46	3.5	0.02
		ETC	4.0	0.55	3.5	0.03
* 0.612 for engines below 85 kW † earlier introduction in selected regions, see Table 1 ‡ only in selected regions, see Table 1

More details on Euro I–III regulations can be found in the section on EU heavy-duty engine standards.

Light duty diesel vehicles

Emission standards for light-duty diesel vehicles (GVW ≤ 3,500 kg) are summarised in Table 4. Ranges of emission limits refer to different classes (by reference mass) of light commercial vehicles; compare the EU light-duty vehicle emission standards for details on the Euro 1 and later standards. The lowest limit in each range applies to passenger cars (GVW ≤ 2,500 kg; up to 6 seats).

Table 4: Emission Standards for Light-Duty Diesel Vehicles, g/km

Year	Reference	CO	HC	HC+NOx	NOx	PM
1992	–	17.3–32.6	2.7–3.7	–	–	–
1996	–	5.0–9.0	–	2.0–4.0	–	–
2000	Euro 1	2.72–6.90	–	0.97–1.70	0.14–0.25	–
2005†	Euro 2	1.0–1.5	–	0.7–1.2	0.08–0.17	–
2010†	Euro III	0.64 0.80 0.95	–	0.56 0.72 0.86	0.50 0.65 0.78	0.05 0.07 0.10
2010‡	Euro 4	0.50 0.63 0.74	–	0.30 0.39 0.46	0.25 0.33 0.39	0.025 0.04 0.06
† earlier introduction in selected regions, see Table 1 ‡ only in selected regions, see Table 1

The test cycle has been the ECE + EUDC for low power vehicles (with maximum speed limited to 90 km/h). Before 2000, emissions were measured over an Indian test cycle.

Engines for use in light-duty vehicles can be also emission tested using an engine dynamometer. The respective emission standards are listed in Table 5.

Table 5: Emission Standards for Light-Duty Diesel Engines, g/kWh

Year	Reference	CO	HC	NOx	PM
1992	–	14.0	3.5	18.0	–
1996	–	11.20	2.40	14.4	–
2000	Euro I	4.5	1.1	8.0	0.36*
2005†	Euro II	4.0	1.1	7.0	0.15
* 0.612 for engines below 85 kW † earlier introduction in selected regions, see Table 1

Light duty gasoline vehicles

4-wheel vehicles

Emissions standards for gasoline vehicles (GVW ≤ 3,500 kg) are summarised in Table 6. Ranges of emission limits refer to different classes of light commercial vehicles (compare the EU light-duty vehicle emission standards). The lowest limit in each range applies to passenger cars (GVW ≤ 2,500 kg; up to 6 seats).

Table 6: Emission Standards for Gasoline Vehicles (GVW ≤ 3,500 kg), g/km

Year	Reference	CO	HC	HC+NOx	NOx
1991	–	14.3–27.1	2.0–2.9	–
1996	–	8.68–12.4	–	3.00–4.36
1998*	–	4.34–6.20	–	1.50–2.18
2000	Euro 1	2.72–6.90	–	0.97–1.70
2005†	Euro 2	2.2–5.0	–	0.5–0.7
2010†	Euro 3	2.3 4.17 5.22	0.20 0.25 0.29	–	0.15 0.18 0.21
2010‡	Euro 4	1.0 1.81 2.27	0.1 0.13 0.16	–	0.08 0.10 0.11
* for catalytic converter fitted vehicles † earlier introduction in selected regions, see Table 1 ‡ only in selected regions, see Table 1

Gasoline vehicles must also meet an evaporative (SHED) limit of 2 g/test (effective 2000).

3- and 2-wheel vehicles

Emission standards for 3- and 2-wheel gasoline vehicles are listed in the following tables.

Table 7: Emission Standards for 3-Wheel Gasoline Vehicles, g/km

Year	CO	HC	HC+NOx
1991	12–30	8–12	–
1996	6.75	–	5.40
2000	4.00	–	2.00
2005 (BS II)	2.25	–	2.00
2010.04 (BS III)	1.25	–	1.25

Table 8: Emission Standards for 2-Wheel Gasoline Vehicles, g/km

Year	CO	HC	HC+NOx
1991	12–30	8–12	–
1996	5.50	–	3.60
2000	2.00	–	2.00
2005 (BS II)	1.5	–	1.5
2010.04 (BS III)	1.0	–	1.0

Table 9: Emission Standards for 2- And 3-Wheel Diesel Vehicles, g/km

Year	CO	HC+NOx	PM
2005.04	1.00	0.85	0.10
2010.04	0.50	0.50	0.05

Overview of the emission norms in India

• 1991 – Idle CO Limits for Gasoline Vehicles and Free Acceleration Smoke for Diesel Vehicles, Mass Emission Norms for Gasoline Vehicles.
• 1992 – Mass Emission Norms for Diesel Vehicles.
• 1996 – Revision of Mass Emission Norms for Gasoline and Diesel Vehicles, mandatory fitment of Catalytic Converter for Cars in Metros on Unleaded Gasoline.
• 1998 – Cold Start Norms Introduced.
• 2000 – India 2000 (Equivalent to Euro I) Norms, Modified IDC (Indian Driving Cycle), Bharat Stage II Norms for Delhi.
• 2001 – Bharat Stage II (Equivalent to Euro II) Norms for All Metros, Emission Norms for CNG & LPG Vehicles.
• 2003 – Bharat Stage II (Equivalent to Euro II) Norms for 13 major cities.
• 2005 – From 1 April Bharat Stage III (Equivalent to Euro III) Norms for 13 major cities.
• 2010 – Bharat Stage III Emission Norms for 2-wheelers, 3-wheelers and 4-wheelers for entire country whereas Bharat Stage – IV (Equivalent to Euro IV) for 13 major cities for only 4-wheelers. Bharat Stage IV also has norms on OBD (similar to Euro III but diluted)

CO₂ emission

India's auto sector accounts for about 18 per cent of the total CO₂ emissions in the country. Relative CO₂ emissions from transport have risen rapidly in recent years, but like the EU, currently there are no standards for CO₂ emission limits for pollution from vehicles.

Obligatory labelling

There is also no provision to make the CO₂ emissions labeling mandatory on cars in the country. A system exists in the EU to ensure that information relating to the fuel economy and CO₂ emissions of new passenger cars offered for sale or lease in the Community is made available to consumers to enable consumers to make an informed choice.

Non-road diesel engines

Further information: Non-road diesel engine

Construction equipment vehicle

Emission standards for diesel construction machinery were adopted on 21 September 2006. The standards are structured into two tiers:

• Bharat (CEV) Stage II—These standards are based on the EU Stage I requirements, but also cover smaller engines that were not regulated under the EU Stage I.
• Bharat (CEV) Stage III—These standards are based on US Tier 2/3 requirements.

The standards are summarised in the following table:

Table 10: Bharat (CEV) Emission Standards for Diesel Construction Machinery

Engine Power	Date	CO	HC	HC+NOx	NOx	PM
kW		g/kWh
Bharat (CEV) Stage II
P < 8	2008.10	8.0	1.3	–	9.2	1.00
8 ≤ P < 19	2008.10	6.6	1.3	–	9.2	0.85
19 ≤ P < 37	2007.10	6.5	1.3	–	9.2	0.85
37 ≤ P < 75	2007.10	6.5	1.3	–	9.2	0.85
75 ≤ P < 130	2007.10	5.0	1.3	–	9.2	0.70
130 ≤ P < 560	2007.10	5.0	1.3	–	9.2	0.54
Bharat (CEV) Stage III
P < 8	2011.04	8.0	–	7.5	–	0.80
8 ≤ P < 19	2011.04	6.6	–	7.5	–	0.80
19 ≤ P < 37	2011.04	5.5	–	7.5	–	0.60
37 ≤ P < 75	2011.04	5.0	–	4.7	–	0.40
75 ≤ P < 130	2011.04	5.0	–	4.0	–	0.30
130 ≤ P < 560	2011.04	3.5	–	4.0	–	0.20

The limit values apply for both type approval (TA) and conformity of production (COP) testing. Testing is performed on an engine dynamometer over the ISO 8178 C1 (8-mode) and D2 (5-mode) test cycles. The Bharat Stage III standards must be met over the useful life periods shown in Table 11. Alternatively, manufacturers may use fixed emission deterioration factors of 1.1 for CO, 1.05 for HC, 1.05 for NO_x, and 1.1 for PM.

Table 11: Bharat (CEV) Stage III Useful Life Periods

Power Rating		Useful Life Period
		hours
< 19 kW		3000
19–37 kW	constant speed	3000
	variable speed	5000
> 37 kW		8000

Agricultural tractors

Emission standards for diesel agricultural tractors are summarised in Table 12.

Table 12: Bharat (Trem) Emission Standards for Diesel Agricultural Tractors

Engine Power	Date	CO	HC	HC+NOx	NOx	PM
kW		g/kWh
Bharat (Trem) Stage I
All	1999.10	14.0	3.5	-	18.0	-
Bharat (Trem) Stage II
All	2003.06	9.0	-	15.0	-	1.00
Bharat (Trem) Stage III
All	2005.10	5.5	-	9.5	-	0.80
Bharat (Trem) Stage III A
P < 8	2010.04	5.5	-	8.5	-	0.80
8 ≤ P < 19	2010.04	5.5	-	8.5	-	0.80
19 ≤ P < 37	2010.04	5.5	-	7.5	-	0.60
37 ≤ P < 56	2011.04	5.0	-	4.7	-	0.40
56 ≤ P < 75	2011.04	5.0	-	4.7	-	0.40
75 ≤ P < 130	2011.04	5.0	-	4.0	-	0.30
130 ≤ P < 560	2011.04	3.5	-	4.0	-	0.20

Emissions are tested over the ISO 8178 C1 (8-mode) cycle. For Bharat (Trem) Stage III A, the useful life periods and deterioration factors are the same as for Bharat (CEV) Stage III, Table 11.

Electricity generation

Generator sets

Emissions from new diesel engines used in generator sets have been regulated by the Ministry of Environment and Forests, Government of India [G.S.R. 371 (E), 17 May 2002]. The regulations impose type approval certification, production conformity testing and labelling requirements. Certification agencies include the Automotive Research Association of India and the Vehicle Research and Development Establishment. The emission standards are listed below.

Table 13: Emission Standards for Diesel Engines ≤ 800 kW for Generator Sets

Engine Power (P)	Date	CO	HC	NOx	PM	Smoke
		g/kWh				1/m
P ≤ 19 kW	2004.01	5.0	1.3	9.2	0.6	0.7
	2005.07	3.5	1.3	9.2	0.3	0.7
19 kW < P ≤ 50 kW	2004.01	5.0	1.3	9.2	0.5	0.7
	2004.07	3.5	1.3	9.2	0.3	0.7
50 kW < P ≤ 176 kW	2004.01	3.5	1.3	9.2	0.3	0.7
176 kW < P ≤ 800 kW	2004.11	3.5	1.3	9.2	0.3	0.7

Engines are tested over the 5-mode ISO 8178 D2 test cycle. Smoke opacity is measured at full load.

Table 14: Emission Limits for Diesel Engines > 800 kW for Generator Sets

Date	CO	NMHC	NOx	PM
	mg/Nm3	mg/Nm3	ppm(v)	mg/Nm3
Until 2003.06	150	150	1100	75
2003.07 – 2005.06	150	100	970	75
2005.07	150	100	710	75

Concentrations are corrected to dry exhaust conditions with 15% residual O₂.

Power plants

The emission standards for thermal power plants in India are being enforced based on Environment (Protection) Act, 1986 of Government of India and it's amendments from time to time. A summary of emission norms for coal- and gas-based thermal power plants is given in Tables 15 and 16.

Table 15: Environmental standards for coal- and gas-based power plants

Capacity	Pollutant	Emission limit
Coal based thermal plants
Below 210 MW	Particulate matter (PM)	350 mg/Nm3
210 MW & above		150 mg/Nm3
500 MW & above		50 mg/Nm3
Gas based thermal plants
400 MW & above	NOX(V/V at 15% excess oxygen)	50 PPM for natural gas; 100 PPM for naphtha
Below 400 MW & up to 100 MW		75 PPM for natural gas; 100 PPM for naphtha
Below 100 MW		100 PPM for naphtha/natural gas
For conventional boilers		100 PPM

Table 16: Stack height requirement for SO₂ control

Power Generation Capacity	Stack Height (Metre)
Less than 200/210 MWe	H = 14 (Q)0.3 where Q is emission rate of SO2 in kg/h, H = Stack height in metres
200/210 MWe or less than 500 MWe 200	200
500 MWe and above	275 (+ Space provision for FGD systems in future)

The norm for 500 MW and above coal-based power plant being practised is 40 to 50 mg/Nm and space is provided in the plant layout for super thermal power stations for installation of flue gas desulphurisation (FGD) system. But FGD is not installed, as it is not required for low sulphur Indian coals while considering SO X emission from individual chimney.

In addition to the above emission standards, the selection of a site for a new power plant has to maintain the local ambient air quality as given in Table 17.

Table 17: Ambient air quality standard

Category	Conc. g/m3
	SPM	SOx	CO	NOx
Industrial and mixed-use	500	120	5000	120
Residential and rural	200	80	2000	80
Sensitive	100	30	1000	30

Table 18: World Bank norms for new projects

Existing Air Quality	Recommendation
SOx > 100 μg/m3	No project
SOx = 100 μg/m3	Polluted area, max. from a project 100 t/day
SOx < 50 μg/m3	Unpolluted area, max. from a project 500 t/day

However the norms for SO_x are even stricter for selection of sites for World Bank funded projects (refer Table 18). For example, if SO_x level is higher than 100 μg/m 3, no project with further SO_x emission can be set up; if SO X level is 100 μg/m 3, it is called polluted area and maximum emission from a project should not exceed 100 t/day; and if SO_x is less than 50 μg/m 3, it is called unpolluted area, but the SO_x emission from a project should not exceed 500 t/day. The stipulation for NOX emission is that its emission should not exceed 260 gram s of NOX per Giga Joule of heat input.

In view of the above, it may be seen that improved environment norms are linked to financing and are being enforced by international financial institutions and not by the policies/laws of land.

Fuels

Fuel quality plays a very important role in meeting the stringent emission regulation.

The fuel specifications of gasoline and diesel have been aligned with the Corresponding European Fuel Specifications for meeting the Euro II, Euro III and Euro IV emission norms.

The use of alternative fuels has been promoted in India both for energy security and emission reduction. Delhi and Mumbai have more than 100,000 commercial vehicles running on CNG fuel. Delhi has the largest number of CNG commercial vehicles running anywhere in the World. India is planning to introduce Biodiesel, ethanol gasoline blends in a phased manner and has drawn up a road map for the same. The Indian auto industry is working with the authorities to facilitate for introduction of the alternative fuels. India has also set up a task force for preparing the Hydrogen road map. The use of LPG has also been introduced as an auto fuel and the oil industry has drawn up plans for setting up of auto LPG dispensing stations in major cities.

Table 19: Indian gasoline specifications

Serial No.	Characteristics	Unit	Bharat Stage II	Bharat Stage III	Bharat Stage IV	Bharat Stage V
1	Density 15 0C	Kg/m3	710–770	720–775	720–775
2	Distillation
3	a) Recovery up to 70 °C(E70) b) Recovery up to 100 0 C (E100) c) Recovery up to 180 0 C (E180) d) Recovery up to 150 0 C (E150) e) Final Boiling Point (FBP), Max f) Residue Max	%Volume %Volume %Volume %Volume °C % Volume	10–45 40–70 90 - 210 2	10–45 40–70 - 75min 210 2	10–45 40–70 - 75min 210 2
4	Research Octane Number (RON), Min		88	91	91
5	Anti Knock Index (AKI)/ MON, Min		84 (AKI)	81 (MON)	81 (MON)
6	Sulphur, Total, Max	% mass	0.05	150 mg/Kg	50 mg/Kg	10 mg/Kg
7	Lead Content(as Pb), Max	g/l	0.013	0.005	0.005
8	Reid Vapour Pressure (RVP), Max	Kpa	35–60	60	60
9	Benzene, Content, Max a) For Metros b)For the rest	% Volume	- 3 5	1	1
10	Olefin content, Max	% Volume	-	21	21
11	Aromatic Content, Max	% Volume	-	42	35<

Table 20: Indian diesel specifications

S. No	Characteristic	BSII	BSIII	BSIV	BSV
1	Density Kg/m3 15 °C	820-800	820–845	820–845
2	Sulphur Content mg/kg max	500	350	50	10
3(a) 3(b)	Cetane Number minimum and / or Cetane Index	48 or 46	51 and 46	51 and 46
4	Polycyclic Aromatic Hydrocarbon	-	11	11
5 (a) (b) (c)	Distillation Reco. Min. At 350 °C Reco. Min. At 370 °C 95%Vol Reco at 0 °C	85 95 -	- - 360	- - 360

Table 21: Diesel Fuel Quality in India

Date	Particulars
1995	Cetane number: 45; Sulfur: 1%
1996	Sulfur: 0.5% (Delhi + selected cities)
1998	Sulfur: 0.25% (Delhi)
1999	Sulfur: 0.05% (Delhi, limited supply)
2000	Cetane number: 48; Sulfur: 0.25% (Nationwide)
2001	Sulfur: 0.05% (Delhi + selected cities)
2005	Sulfur: 350 ppm (Euro 3; selected areas)
2010	Sulfur: 350 ppm (Euro 3; nationwide)
2010	Sulfur: 50 ppm (Euro 4; selected areas)
2020 (proposed)	Sulfur: 10ppm (Euro 5; entire country)

Table 22: Indian bio-diesel specifications

S. No.	Characteristics	Requirement	Method of Test, ref to
			Other Methods	[P:] of IS 1448
(1)	(2)	(3)	(4)	(5)
i.	Density at 15 °C, kg/m3	860–900	ISO 3675	P:16/
			ISO 12185	P:32
			ASTM
ii.	Kinematic Viscosity at 40 °C, cSt	2.5–6.0	ISO 3104	P:25
iii.	Flash point (PMCC) °C, min	120	P:21
iv.	Sulphur, mg/kg max.	50.0	ASTM D 5453	P:83
v	Carbon residue (Ramsbottom) *,% by mass, max	0.05	ASTM D 4530ISO 10370	-
vi.	Sulfated ash, % by mass, max	0.02	ISO 6245	P:4
vii.	Water content, mg/kg, max	500	ASTM D 2709	P:40
			ISO 3733
			ISO 6296
viii	Total contamination, mg/kg, max.	24	EN 12662	-
ix	Cu corrosion, 3 h at 50 °C, max	1	ISO 2160	P:15
x	Cetane No., min	51	ISO 5156	P:9
xi	Acid value, mg KOH/g, max	0.50	-	P:1 / Sec 1
xii	Methanol @, % by mass, max	0.20	EN 14110	-
xiii	Ethanol, @@ % by mass, max	0.20	-
xiv	Ester content, % by mass, min	96.5	EN 14103	-
xv	Free Glycerol, % by mass, max	0.02	ASTM D 6584	-
xvi	Total Glycerol, % by mass, max	0.25	ASTM D 6584	-
xvii	Phosphorus, mg/kg, max	10.0	ASTMD 4951	-
xviii	Sodium & Potassium, mg/kg, max	To report	EN 14108 &	-
			EN 14109	-
xix	Calcium and Magnesium, mg/kg, max	To report	**	-
xx	Iodine value	To report	EN 14104	-
xxi	Oxidation stability, at 110 °C h, min	6	EN 14112	-
* Carbon residue shall be run on 100% sample ** European method is under development @ Applicable for Fatty Acid Methyl Ester @@ Applicable for Fatty Acid Ethyl Ester

Criticism and commentary

Ineffectiveness of present pollution control system

Presently, all vehicles need to undergo a periodic emission check (3 months/ 6 months) at PUC Centres at Fuel Stations and Private Garages which are authorised to check the vehicles. In addition, transport vehicles need to undergo an annual fitness check carried out by RTOs for emissions, safety and roadworthiness.

The objective of reducing pollution not achieved to a large extent by the present system. Some reasons for this are: – Independent centres do not follow rigorous procedures due to inadequate training – Equipment not subjected to periodic calibration by independent authority – Lack of professionalism has led to malpractice – Tracking system of vehicles failing to meet norms non-existent

Comparison between Bharat Stage and Euro norms

The Bharat Stage norms have been styled to suit specific needs and demands of Indian conditions. The differences lie essentially in environmental and geographical needs, even though the emission standards are exactly the same.

For instance, Euro-III is tested at sub-zero temperatures in European countries. In India, where the average annual temperature ranges between 24 and 28 degree Celsius, the test is done away with.

Another major distinction is in the maximum speed at which the vehicle is tested. A speed of 90 km/h is stipulated for BS-III, whereas it is 120 km/h for Euro-III, keeping emission limits the same in both cases

In addition to limits, test procedure has certain finer points too. For instance, the mass emission test measurements done in g/km on a chassis dynamometer requires a loading of 100 kg weight in addition to unloaded car weight in Europe. In India, BS-III norms require an extra loading of 150 kg weight to achieve the desired inertia weight mainly due to road conditions here.

Non-existence of CO₂ limits

Various groups and agencies have criticised the government and urged the government of India to draft mandatory fuel efficiency standards for cars in the country, or at least to make the CO₂ emissions labelling mandatory on all new cars in the country. The auto companies should inform the customers about a vehicle's emissions.

Lag behind Euro standards

There has been criticism of the fact that the Indian norms lag the Euro norms. As of 2014, only a few cities meet Euro IV or Bharat Stage IV standards that are nine years behind Europe. The rest of India gets Bharat Stage III standard fuel and vehicles, which are 14 years behind Europe. Also, there was a suggestion from some bodies to implement Euro IV norms after Euro II norms, skipping the Euro III norms totally. This is because the Euro III norms are only a small improvement over Euro II, whereas Euro IV norms mark a big leap over Euro II. According to a study conducted by the Desert Research Institute and the Indian Institute of Technology Delhi, the only way to stabilise fine particulates (PM2.5) at the 2011 levels despite the five-fold rise in vehicular density is nationwide implementation of Bharat V standards by 2015.

Cycle beating

For the emission standards to deliver real emission reductions it is crucial that the test cycles under which the emissions have to comply as much as possible reflect normal driving situations. It was discovered that manufacturers of engine would engage in what was called 'cycle beating' to optimise emission performance to the test cycle, while emissions from typical driving conditions would be much higher than expected, undermining the standards and public health. In one particular instance, research from two German technology institutes found that for diesel cars no 'real' NOx reductions have been achieved after 13 years of stricter standards.

Need for uniform emissions standards across the country

The practice of limiting improved emissions standards only to a few cities and to a smaller proportion of urban population has been criticised as violating the fundamental right to healthy life for all. This also does not allow trucks to move to cleaner fuel and technology and they heavily pollute cities during transit and aggravate pollution in cities. Many persons and establishments try to purchase Bharat Stage III vehicles and fuel from outside city limits in order to take advantage of lower prices, even though these are used in cities.

Regulatory framework

In India the Rules and Regulations related to driving license, registration of motor vehicles, control of traffic, construction & maintenance of motor vehicles etc. are governed by the Motor Vehicles Act 1988 (MVA) and the Central Motor Vehicles rules 1989 (CMVR). The Ministry of Shipping, Road Transport & Highways (MoSRT&H) acts as a nodal agency for formulation and implementation of various provisions of the Motor Vehicle Act and CMVR.

To involve all stake holders in regulation formulation, MoSRT&H has constituted two Committees to deliberate and advise Ministry on issues relating to Safety and Emission Regulations, namely –

• CMVR- Technical Standing Committee (CMVR-TSC)
• Standing Committee on Implementation of Emission Legislation (SCOE)

CMVR- Technical Standing Committee (CMVR-TSC)

This Committee advises MoSRT&H on various technical aspects related to CMVR. This Committee has representatives from various organisations namely; Ministry of Heavy Industries & Public Enterprises (MoHI&PE)), MoSRT&H, Bureau Indian Standards (BIS), Testing Agencies such as Automotive Research Association of India (ARAI),International Center for Automotive Technology (ICAT - www.icat.in), Vehicle Research Development & Establishment (VRDE), Central Institute of Road Transport (CIRT), industry representatives from Society of Indian Automobile Manufacturers (SIAM), Automotive Component Manufacturers Association (ACMA) and Tractor Manufacturers Association (TMA) and representatives from State Transport Departments. Major functions the Committee are:

• To provide technical clarification and interpretation of the Central Motor Vehicles Rules having technical bearing, to MoRT&H, as and when so desired.
• To recommend to the Government the International/ foreign standards which can be used in lieu of standard notified under the CMVR permit use of components/parts/assemblies complying with such standards.
• To make recommendations on any other technical issues which have direct relevance in implementation of the Central Motor Vehicles Rules.
• To make recommendations on the new safety standards of various components for notification and implementation under Central Motor Vehicles Rules.
• To make recommendations on lead time for implementation of such safety standards.
• To recommend amendment of Central Motor Vehicles Rules having technical bearing keeping in view of Changes in automobile technologies.

CMVR-TSC is assisted by another Committee called the Automobile Industry Standards Committee (AISC) having members from various stakeholders in drafting the technical standards related to Safety. The major functions of the committee are as follows:

• Preparation of new standards for automotive items related to safety.
• To review and recommend amendments to the existing standards.
• Recommend adoption of such standards to CMVR Technical Standing Committee
• Recommend commissioning of testing facilities at appropriate stages.
• Recommend the necessary funding of such facilities to the CMVR Technical Standing Committee, and
• Advise CMVR Technical Standing Committee on any other issues referred to it

The National Standards for Automotive Industry are prepared by Bureau of Indian Standards (BIS). The standards formulated by AISC are also converted into Indian Standards by BIS. The standards formulated by both BIS and AISC are considered by CMVR-TSC for implementation.

Standing Committee on Implementation of Emission Legislation (SCOE)

This Committee deliberates the issues related to implementation of emission regulation. Major functions of this Committee are –

• To discuss the future emission norms
• To recommend norms for in-use vehicles to MoSRT&H
• To finalise the test procedures and the implementation strategy for emission norms
• Advise MoSRT&H on any issue relating to implementation of emission regulations.

Based on the recommendations from CMVR-TSC and SCOE, MoSRT&H issues notification for necessary amendments / modifications in the in Central Motor Vehicle Rules.

In addition, the other Ministries like Ministry of Environment & Forest (MoEF), Ministry of Petroleum & Natural Gas (MoPNG) and Ministry of Non-conventional Energy Sources are also involved in formulation of regulations relating to Emissions, Noise, Fuels and Alternative Fuel vehicles.

See also

• Air pollution in India
• Automotive Industry Standards