Piping and instrumentation diagram

A piping and instrumentation diagram/drawing (P&ID) is a detailed diagram in the process industry which shows the piping and vessels in the process flow, together with the instrumentation and control devices.

Superordinate to the piping and instrumentation flowsheet is the process flow diagram (PFD) which indicates the more general flow of plant processes and equipment and relationship between major equipment of a plant facility.

Contents and function

Piping and instrumentation diagram of pump with storage tank. Symbols according to EN ISO 10628 and EN 62424.

A more complex example of a P&ID.

A piping and instrumentation diagram/drawing (P&ID) is defined by the Institute of Instrumentation and Control as follows:

A diagram which shows the interconnection of process equipment and the instrumentation used to control the process. In the process industry, a standard set of symbols is used to prepare drawings of processes. The instrument symbols used in these drawings are generally based on International Society of Automation (ISA) Standard S5.1
The primary schematic drawing used for laying out a process control installation.

They usually contain the following information:

Process piping, sizes and identification, including:
- Pipe classes or piping line numbers
- Flow directions
- Interconnections references
- Permanent start-up, flush and bypass lines
Mechanical equipment/ Process control instrumentation and designation (names, numbers, unique tag identifiers), including:
- Valves and their identifications (e.g. isolation, shutoff, relief and safety valves)
- Control inputs and outputs (sensors and final elements, interlocks)
- Miscellanea - vents, drains, flanges, special fittings, sampling lines, reducers and increasers
Interfaces for class changes
Computer control system
Identification of components and subsystems delivered by others

P&IDs are originally drawn up at the design stage from a combination of process flow sheet data, the mechanical process equipment design, and the instrumentation engineering design. During the design stage, the diagram also provides the basis for the development of system control schemes, allowing for further safety and operational investigations, such as a Hazard and operability study (HAZOP). To do this, it is critical to demonstrate the physical sequence of equipment and systems, as well as how these systems connect.

P&IDs also play a significant role in the maintenance and modification of the process after initial build. Modifications are red-penned onto the diagrams and are vital records of the current plant design.

They are also vital in enabling development of;

Control and shutdown schemes
Safety and regulatory requirements
Start-up sequences
Operational understanding.

P&IDs form the basis for the live mimic diagrams displayed on graphical user interfaces of large industrial control systems such as SCADA and distributed control systems.

Identification and reference designation

Based on STANDARD ANSI/ISA S5.1 and ISO 14617-6, the P&ID is used for the identification of measurements within the process. The identifications consist of up to 5 letters. The first identification letter is for the measured value, the second is a modifier, 3rd indicates passive/readout function, 4th - active/output function, and the 5th is the function modifier. This is followed by loop number, which is unique to that loop. For instance FIC045 means it is the Flow Indicating Controller in control loop 045. This is also known as the "tag" identifier of the field device, which is normally given to the location and function of the instrument. The same loop may have FT045 - which is the flow transmitter in the same loop.

Letter	Column 1 (Measured value)	Column 2 (Modifier)	Column 3 (Readout/passive function)	Column 4 (Output/active function)	Column 5 (Function modifier)
A	Analysis		Alarm
B	Burner, combustion		User choice	User choice	User choice
C	User's choice (usually conductivity)			Control	Close
D	User's choice (usually density)	Difference			Deviation
E	Voltage		Sensor
F	Flow rate	Ratio
G	User's choice (usually gaging/gauging)	Gas	Glass/gauge/viewing
H	Hand				High
I	Current		Indicate
J	Power	Scan
K	Time, time schedule	Time rate of change		Control station
L	Level		Light		Low
M	User's choice				Middle / intermediate
N	User's choice (usually torque)		User choice	User choice	User choice
O	User's choice		Orifice		Open
P	Pressure		Point/test connection
Q	Quantity	Totalize/integrate	Totalize/integrate
R	Radiation		Record		Run
S	Speed, frequency			Switch	Stop
T	Temperature			Transmit
U	Multivariable		Multifunction	Multifunction
V	Vibration, mechanical analysis			Valve or damper
W	Weight, force		Well or probe
X	User's choice (usually on-off valve as XV)	X-axis	Accessory devices, unclassified	Unclassified	Unclassified
Y	Event, state, presence	Y-axis		Auxiliary devices
Z	Position, dimension	Z-axis or Safety		Actuator, driver or unclassified final control element

For reference designation of any equipment in industrial systems the standard IEC 61346 (Industrial systems, installations and equipment and industrial products — Structuring principles and reference designations) can be applied. For the function Measurement the reference designator B is used, followed by the above listed letter for the measured variable.

For reference designation of any equipment in a power station the KKS Power Plant Classification System can be applied.

Symbols of chemical apparatus and equipment

Below are listed some symbols of chemical apparatus and equipment normally used in a P&ID, according to ISO 10628 and ISO 14617.

**Symbols of chemical apparatus and equipment**
Pipe	Thermally insulated pipe	Jacketed pipe	Cooled or heated pipe
Jacketed mixing vessel (autoclave)	Half pipe mixing vessel	Pressurized horizontal vessel	Pressurized vertical vessel
Pump	Vacuum pump or compressor	Bag	Gas bottle
Fan	Axial fan, ,MK,,,	Radial fan	Dryer
Packed column	Tray column	Furnace	Cooling tower
Heat exchanger	Heat exchanger	Cooler	Plate & frame heat exchanger
Double pipe heat exchanger	Fixed straight tubes heat exchanger	U shaped tubes heat exchanger	Spiral heat exchanger
Covered gas vent	Curved gas vent	(Air) filter	Funnel
Steam trap	Viewing glass	Pressure reducing valve	Flexible pipe
Valve	Control valve	Manual valve	Back draft damper
Needle valve	Butterfly valve	Diaphragm valve	Ball valve